Waterco INFINIUM ECO-V150 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 17

Waterco INFINIUM ECO-V150 Скачать руководство пользователя страница 4

INFINIUM ∞ ECO-V150

Variable Speed Pump

I pg 05

Commercial pools and spas constructed prior to December 19, 2008, with a single
submerged suction outlet shall use a suction outlet cover that meets ASME/ANSI
A112.19.8a and either:

• A SVRS meeting ASME/ANSI A112.19.17 and/or ASTM F2387, or

• A properly designed and tested suction-limiting vent system, or

• An automatic pump shut-off system, or

• Disabled submerged outlets, or

• Suction outlets shall be reconfigured into return inlets.

Pump Overview

The perfect choice for all types of pools,
the Infinium Eco-V Variable Speed Pump as
specifically designed to be your best choice
for a variety of in-ground pools.

Thick walled body parts, a heavy duty TEFC
motor, and highly engineered hydraulics
make this rugged and tested design perfect
for any pool, spa, water feature, or fountain.

All pumps from Waterco incorporate
innovative hydraulic engineering that has
been refined for over 40 years.

Compact, rugged, and easy to maintain, the
Infinium Eco-V pump will deliver years of
reliable service.

Pump Controller Features

Simple user interface
Motor design reduces noise emissions
UV and rain-proof enclosure
Manual OVERRIDE
High efficiency electromechanical motor and
control design

General Features

Extremely quiet operation
Unionized fittings (1.5” and 2”) for simple
replacement
Screw on lid for easy cleaning and
maintenance
Heavy-duty TEFC motor for long life
Integral volute and pot reduce hydraulic
noise
See-through lid permits easy inspection of
strainer basket
Self-priming for quick, easy start-up
IAPMO Listed and tested to UL 1081

«
...
2
3
4
5
6
...
»

Содержание INFINIUM ECO-V150


















Отзывы:

Нет отзывов