INFINIUM ∞ ECO-V150
Variable Speed Pump
I pg 21
4. This sequence will then repeat for STEP 2 and then STEP 3 with- out the INFINIUM ECO
V-150 stopping.
5. At the end of STEP 3, the INFINIUM ECO V-150 will wait if necessary for the completion of
the 24-hour schedule. During this waiting period (if applicable), all of the “active step LEDs”
will remain OFF. However, the START LED will still be illuminated. After completion of the
24 hour schedule, the system restarts at STEP 1 and this cycle will repeat indefinitely until
the user presses the STOP key.
NOTE:
Pressing a STEP key other than for the STEP currently running will cause an immediate
transition to the newly selected STEP. The INFINIUM ECO V-150 will continue with the
programmed schedule from that point forward.
NOTE:
If STOP is pressed during normal schedule operation, the 24 hour schedule will stop.
When START is pressed again, the 24 hour schedule will start from STEP 1.
NOTE:
If power is lost while the INFINIUM ECO V-150 is running a 24 hour schedule, upon
restoration of power the INFINIUM ECO V-150 will start the 24 hour schedule from STEP 1.
NOTE:
If a digital input (provided from an external source) is detected, the INFINIUM ECO
V-150 will start running on the STEP 1, STEP 2, STEP 3, or OVERRIDE speed corresponding
to the digital input. Upon removing the digital input (provided from an external source), the
INFINIUM ECO V-150 will stop and the user will need to press START to begin the 24 hour
schedule operation. However, if START was already pressed prior to receiving a digital input,
then the INFINIUM ECO V-150 will resume running the 24 hour schedule once the digital input
is removed.
NOTE:
Pressing STOP at any time turns the INFINIUM ECO V-150 OFF and clears the start time
for the 24 hour schedule.
OVERRIDE
The INFINIUM ECO V-150 is equipped with an OVERRIDE feature, which can be engaged
to temporarily run at higher or lower speeds ranging between 600 to 3450 RPM. Once the
OVERRIDE duration has elapsed, the INFINIUM ECO V-150 will automatically return to the
programmed schedule.
1. Pressing the OVERRIDE key while the INFINIUM ECO V-150 is running will cause
the INFINIUM ECO V-150 to start running in the OVERRIDE mode at the programmed
DURATION and SPEED. The “active LED” for OVERRIDE will illuminate. The DURATION
and SPEED setting LEDs along with its respective bar graph LED will blink back and forth
at three (3) second intervals.
2. The UP (+) / DOWN (-) arrows allow the user to configure OVER RIDE DURATION and
SPEED. These settings can be changed while the INFINIUM ECO V-150 is running. These
settings are stored each time the UP (+) / DOWN (-) arrows are pressed.
NOTE: When the OVERRIDE duration ends, the INFINIUM ECO V-150 resumes the 24 hour
schedule at the point in the currently programmed 24 hour schedule where it normally would be
running at that time. The OVER- RIDE duration will not affect the start or stop times of the 24
hour schedule. For example, if OVERRIDE runs during a period overlapping with a later part of
STEP 1 and an early part of STEP 2, the start time of STEP 3 is not affected.
NOTE:
Pressing/Holding OVERRIDE key for more than three (3) seconds will cancel OVERRIDE
mode.
NOTE:
During the OVERRIDE mode, the INFINIUM ECO V-150 will not start with the priming
sequence.
NOTE:
It is recommended that you do not set the OVERRIDE duration to 0 HRS. Setting the
OVERRIDE duration to 0 HRS will not allow you to change the duration setting while the motor
is running. The motor will have to be stopped in order to change the OVERRIDE settings if the
duration is set to 0 HRS.
Schedule Advance
The Schedule Advance mode allows the user to press the START button at one time of the day,
with the 24-hour schedule starting at a different time of day. The INFINIUM ECO V-150 can
run in the Schedule Advance mode (by using the OVERRIDE button) and upon completion will
begin the programmed 24 hour schedule at STEP 1 DURATION and SPEED.
The following steps should be followed to set Schedule Advance mode:
1. With the INFINIUM ECO V-150 stopped, press and hold the START key for more than three
(3) seconds. The START LED will blink at a rate of one second per pulse. The DURATION
setting LED and respective bar graph LED will remain turned ON until the Schedule
Advance mode is complete.
2. Press the UP (+) or DOWN (-) arrows to set the desired delay time after which the 24-
hour schedule should start. The Schedule Advance mode will automatically start after the
desired delay time is selected. The Schedule Advance mode can be canceled by pressing
the STOP key.
NOTE:
The OVERRIDE button will still function when the Schedule Advance mode is active.
This will allow the user to run the INFINIUM ECO V-150 during the period of the Schedule
Advance mode.
NOTE:
While the INFINIUM ECO V-150 is in the Schedule Advance mode, if a user presses
STEP 1, STEP 2, STEP 3 or the START key, the system will start the normal schedule and the
Schedule Advance mode will be canceled.
NOTE:
While the INFINIUM ECO V-150 is in the Schedule Advance mode, if a user presses the
STOP key, then the Schedule Advance mode is canceled.
NOTE:
If power is lost while the INFINIUM ECO V-150 is in the Schedule Advance mode, then
the 24-hour schedule will automatically start when power is restored.
!
DANGER
Do not perform any maintenance on the motor while the motor is in Schedule Advance
Mode. The motor may start without warning. This event could cause death or serious
personal injury.