Watchguard SMS 2010 WGSMS2010 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 47

background image

8

2. Installation

2.1 Planning the Installation

To get the best possible protection from your Watchguard SMS 2010 alarm system, it is imperative that you
follow the following guidelines on where to place the system components. Below is a diagram of typical
locations to place the Main Control Unit and wireless accessories.

2.2 Installation Sequence

A variety of accessories are available with the Watchguard SMS 2010 alarm system. This guide provides
installation details for each of these accessories, following the setting up of the SIM Card and the mounting of
the main control unit.

1.  Setting up the SIM Card.
2.  Main Control Unit.
3.  Install Accessories.

Once the

Main Control Unit

is mounted, you will then need to set-up and install any accessories you

have.

a.  Wireless PIR Motion Detectors
b.  Panic Buttons
c.  Smoke Detectors
d.  Wireless Reed Switch and Shock Sensors
e.  External Hard-Wired/Wireless Sirens
f.

Wireless Keypad

4. Configure Arm/Disarm Confirmation Reports.
5. Customise Programming.

«
...
6
7
8
9
10
...
»

Содержание SMS 2010 WGSMS2010
















































Отзывы:

Нет отзывов

Похожие инструкции для SMS 2010 WGSMS2010

Бренд: Abicor Binzel Страницы: 42

Бренд: Nady Systems Страницы: 8

Бренд: RainSoft Страницы: 16

Бренд: 4xem Страницы: 68

iMEGAPRO IPR7922E

Бренд: Lilin Страницы: 12

Бренд: ACS Страницы: 64

Бренд: Vivotek Страницы: 2

Бренд: Abus Страницы: 311

Vingtor Stentofon SPA-AC6

Бренд: Zenitel Страницы: 54

Бренд: 3xLogic Страницы: 17

Бренд: M-system Страницы: 2

Бренд: Guardian Audio Страницы: 4

Бренд: AccuTools Страницы: 6

Бренд: THORLABS Страницы: 18

Trailblazer 251

Бренд: Miller Страницы: 48

Бренд: Axis Страницы: 51

Бренд: V-GREAT Страницы: 2

Бренд: THORLABS Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды