Wallenstein BXTR6438F Скачать руководство пользователя страница 49

Страница: 49 / 68

BXTR6438

5.9 Drive Belt Replacement

This procedure is for models BXTR6438 and

BXTR6438P
1. Remove the 3 bolts that secure the belt shield,

and remove the shield.

2. Loosen (do not remove) the 4 x engine nuts that

hold the engine sub frame to the main frame (lo

cated under the main frame).

3. Turn the belt tensioning nut counter clockwise,

until the drive belt is loose enough to remove,

then remove the belts.

4. Replace with the new dual band belt. Turn the

belt tensioning nuts clockwise, to tighten the belt

(ensure you tighten both nuts equally).

5. Check the tension by pushing on the belt with your

fore finger and measure its defection. Drive belt

should deflect no more than 3/8 to 7/16". (10 mm

to 12 mm)

6. When tension is correct, check pulley alignment

then tighten up all four engine sub frame bolts,

and replace the belt shield, cover and reinstall

the bolts.

7. Recheck tension after 10 hours of use.

Belt Tension Nut:

To tighten turn clockwise

To loosen turn counter-clockwise.

Engine

Nuts (4)

Drive Belt

View Under

Engine Support

Engine

Support

Содержание BXTR6438F





































































Результаты поиска

Содержание BXTR6438F

Отзывы:

Похожие инструкции для BXTR6438F

Бренды по названию

Популярные бренды

Wallenstein BXTR6438F, Руководство оператора

Результаты поиска

Содержание BXTR6438F

Отзывы:

Похожие инструкции для BXTR6438F

Бренды по названию

Популярные бренды