Wallenstein BXTR6438F Скачать руководство пользователя страница 44

Страница: 44 / 68

BXTR6438

Location

Grease Points - 50 hrs or Annually

Engine Adjustment Plate

Right Wheel Bearing

Discharge Chute Adjustment Ring

Rotor Main Shaft Rear Roller Flange

Grease with one shot of grease.

Location Lubricate Hinges & Pivot Points

Lid Hinges (fuel, hydraulic, tool)

Hitch Coupler

Tongue Jack

Inspect daily, lubricate every 40 hours or

weekly.

Rotor blades: check daily,

test sharpness every 50 hr

Machine is shown with guard removed

for illustrative purposes only. Do not

operate machine with guard removed.

WARNING

Every 100 hr or annually. wash

and clean wood chipper, re

move entangled material, wood

chips, small debris.

Hydraulic Filter:

replace every 100

hr or annually.

Battery: check every

50 hr.

Belt drive: Check tension daily,

adjust every 50 hr.

Check sheave alignment every

50 hr.

Fuel: check daily or

every 8 hr, treat fuel

if not being used for

long periods of time.

Hydraulic Oil: check

daily, inspect every 50

hr.

Tire Pressure:

check every

100 hr or

annually.

On a regular basis check the condition of all hydraulic

lines, hoses and fittings. Replace any that are dam-

aged. Re-route those that are rubbing, pinched or

crimped. Tighten any fitting that is leaking. Ensure

fittings are clean and free of dirt.

Содержание BXTR6438F





































































Результаты поиска

Содержание BXTR6438F

Отзывы:

Похожие инструкции для BXTR6438F

Бренды по названию

Популярные бренды

Wallenstein BXTR6438F, Руководство оператора

Результаты поиска

Содержание BXTR6438F

Отзывы:

Похожие инструкции для BXTR6438F

Бренды по названию

Популярные бренды