Wallenstein BXT36S, Руководство оператора

Страница: 26 / 72

6.2 Pre-Start Checklist
Complete the following before you start the machine the first
time and every time thereafter:
Items to Complete
Read and obey the Operating Safety on page 25 , Engine
Operation Safety on page 27, and Fuel Safety on page
28.
Check the drive belt tension and alignment. If necessary,
adjust the drive belt.
For instructions, see Set the Drive Belt Tension on page
54, and Align the Drive Belt on page 55.
Check the condition and clearance of the twig breaker,
rotor knives, and ledger knife. If necessary, adjust or
replace them.
Check the engine oil level. For instructions, see Check the
Engine Oil Level on page 29 . If necessary, add oil.
Check the engine fuel level. For instructions, see Check the
Fuel Level on page 28 . If necessary, add fuel.
Check the engine air filter. For instructions, see Clean the
Engine Air Filter on page 50 . If necessary, clean or
replace the filter.
Check the condition of the battery and electrical
components. Make sure that all of the electrical
components are in working condition and the connectors
are connected. Replace damaged or corroded electrical
components.
Make sure that the machine is lubricated, as specified in
the Maintenance Schedule on page 46 .
Remove anything that is entangled on the machine. For
example, branches or vines.
Remove all material from the rotor housing and discharge
chute. For example, wood chips, bark, or leaves. Material
in the rotor housing can cause the engine to stall when you
start the machine.
Make sure that the rotor bearings turn freely.
If the bearings are damaged or do not turn freely, lubricate
them or contact your local Wallenstein dealer to have them
replaced.
Make sure that all guards and shields are installed, and
the covers are closed. If necessary, replace the guards,
shields, or covers.
Check the condition of the chipper hopper safety curtain.
Replace the safety curtain if it is damaged. For more
information, see Safety Curtain Maintenance on page
61.
Check the tire air pressure, and the wheels, hubs, and axle.
See the side of the tire for the correct air pressure.
Make sure that all the fasteners are installed and torqued to
the correct specifications. For more information, see Bolt
Torque on page 65 and Lug Nut Torque on page 66.
Items to Complete
Make sure that the operator and spotter are wearing the
necessary PPE. The PPE must be in good condition.
Make sure that the operator and spotter are not wearing
loose-fitting clothing or jewelry, and long hair is tied up.
Make sure that there are no bystanders inside the work
zone and the spotter is not near a hazard. For zone
definitions, see Work Site on page 11.
6.3 Machine Break-In
Before and during the first eight hours of operation, do the
following tasks.
6.3.1 Before Initial Startup
1. Read and understand all safety information in this manual
and the engine manufacturer's manual.
2. Review the Machine Components on page 19 .
3. Review the operation and function of the Controls on page
21 .
4. Complete the Pre-Start Checklist on page 26 .
6.3.2 After One to Five Hours of Operation
• Check the drive belt tension and alignment. If necessary,
adjust the drive belt.
For instructions, see
Drive Belt Maintenance on page 53 .
• Check the condition and clearance of the twig breaker, rotor
knives, and ledger knife. If necessary, adjust or replace
them.
• After five hours of operation, change the engine oil. For
instructions, see the engine manufacturer's manual.
• Check the engine oil level. If necessary, add oil. For
instructions, see
Check the Engine Oil Level on page 29 .
• Check the engine fuel level. If necessary, add fuel. For
instructions, see
Check the Fuel Level on page 28 .
• Make sure that all of the electrical components are in
working condition and the connectors are connected.
• Check the condition of the rotor bearings. Make sure that
the rotor bearings turn freely.
• Check the fasteners and make sure that they are torqued to
the correct specifications. For more information, see
Bolt
Torque on page 65 and Lug Nut Torque on page 66.
• Check the tire air pressure, and the wheels, hubs, and axle.
See the side of the tire for the correct air pressure.
• Remove material that is entangled on the machine.
• Remove material from the rotor housing and discharge
chute.
Operating Instructions
BXT36S
Wood Chipper
26