W & A Delta Plow Скачать руководство пользователя страница 50

Страница: 50 / 70

308.708.8185 | [email protected] | Rev. 11/20

RETURN TO INDEX

CHECKING BOLT TORQUE

The table shown below gives correct torque values for various bolts and capscrews. Tighten all bolts

to the torques specified in chart unless otherwise noted. Check tightness of bolts periodically, using

bolt torque chart as a guide. Replace hardware with the same grade bolt.

Torque Specifications

Bolt Diameter

Bolt Torque*

SAE Grade 2

SAE Grade 5

SAE Grade 8

INCH

lbft

(Nm)

lbft

(Nm)

lbft

(Nm)

1/4

(8)

(12)

(17)

5/16

(13)

(25)

(36)

3/8

(27)

(45)

(63)

7/16

(41)

(72)

(100)

1/2

(61)

(110)

115

(155)

9/16

(95)

115

(155)

165

(220)

5/8

(128)

160

(215)

220

(305)

3/4

165

(225)

290

(390)

400

(540)

7/8

170

(230)

420

(570)

650

(880)

226

(345)

630

(850)

970

(1320)

BOLT HEAD IDENTIFICATION

Grade 2

Grade 5

Grade 8

BOLT TORQUE CHART

MAINTENANCE & LUBE

Содержание Delta Plow







































































Результаты поиска

Содержание Delta Plow

Отзывы:

Похожие инструкции для Delta Plow

Бренды по названию

Популярные бренды

W & A Delta Plow, Руководство пользователя

Результаты поиска

Содержание Delta Plow

Отзывы:

Похожие инструкции для Delta Plow

Бренды по названию

Популярные бренды