manualshive.com logo in svg

W & A Delta Plow, Руководство пользователя

Поделиться
Скачать
W & A Delta Plow Скачать руководство пользователя страница 39

39

308.708.8185 | [email protected] | Rev. 11/20

RETURN TO INDEX

While operating the Delta Plow in the field, the wings will need to be held down to prevent the wing 

from riding up. In order to work properly, the wings need to be leveled according to the leveling 

procedure on page 26.

DELTA PLOW HYDRAULIC WING DOWN FORCE OPERATION:

FIELD OPERATION - WING DOWN PRESSURE

1.  Unfold the wings of the Delta Plow

2.  Once unfolded, engage the SCV of the tractor with the flow set very low in the direction 

       of unfolding. This will allow the cylinders to keep pushing the wings down and prevent the  

       wings from riding up.

OPERATION

Pressure Flow

•  Recommended remote valve flow should be set at 10%-20% of 

maximum flow.

•  If wings are not staying level, increase the flow in 5% increments until 

operating correctly. Do not exceed 40% flow.

Содержание Delta Plow







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды