W & A Delta Plow Скачать руководство пользователя страница 33

Страница: 33 / 70

308.708.8185 | [email protected] | Rev. 11/20

RETURN TO INDEX

DANGER

LOSS OF CONTROL HAZARD:

Ensure that the towing vehicle is adequate for the task. Using an inadequate tow vehicle

is extremely unsafe, and can result in loss of control, serious injury and death. To reduce

the hazard, use only a 3-point towing vehicle that is both rated for the implement load,

and properly ballasted for the load.

ELECTRICAL SHOCK/ELECTROCUTION HIGH-CLEARANCE DANGER:

•

Keep clear of overhead power lines, maintain 20-foot minimum distance. Electrical

shock and/or electrocution can occur; will result in death or serious injury.

•

Hazards may include, but are not limited to, high clearance equipment, low clearance

power lines, lack of awareness of surroundings, etc.

BRAKING AND LOSS OF CONTROL HAZARD:

Do not exceed 20 mph (32km/h) when driving straight. Do not exceed 13 mph (21 km/h)

in turns. The weight of the implement can cause under-steer, and the height of the

implement is a tipping hazard.

CAUTION

DANGER

TRANSPORT CHECKLIST

Before transporting the implement, check the following items.

Transport only with a tractor of proper size and adequate ballast.

Hitch implement securely to tractor. See “Hitching Tractor to Implement” on page 14.

Plug implement safety lights into tractor seven-pin connector.

Make sure implement is folded properly. See “Folding” on page 31. Raise the implement for adequate

ground clearance.

Comply with all national, regional, and local safety laws when traveling on public roads.

Travel with caution.

OPERATION

Содержание Delta Plow







































































Результаты поиска

Содержание Delta Plow

Отзывы:

Похожие инструкции для Delta Plow

Бренды по названию

Популярные бренды

W & A Delta Plow, Руководство пользователя

Результаты поиска

Содержание Delta Plow

Отзывы:

Похожие инструкции для Delta Plow

Бренды по названию

Популярные бренды