VSCOM NetCom Plus 111 Скачать руководство пользователя страница 45

Страница: 45 / 133

4 Windows Virtual COM Driver

4.4.5 Installation of NetCom Plus Servers

This section of the manual covers the correct installation of the drivers and serial ports. Please
do a quick review of the section

4.1

, before reading further. As of the time of writing, the current

driver is version 2.0.0.0

Figure 35: Select NetCom

to install

The NetCom Plus Manager program is automatically started by the Installation Wizard, or later
intentionally by the user (see fig.

). There are different ways the NetCom

servers are listed.

Figure 36: New NetCom

The first time a NetCom

is detected it is displayed in blue

color. This indicates a “New” status, i.e. it is not yet installed
in the system, but it is ready to. When the NetCom Plus
Manager is closed by the

button the server and the serial

ports on it are installed in the operating system.

Figure 37: Installed NetCom

When the NetCom Plus Manager is started a second time,
usually the NetCom

in the network are already installed in

Windows. Then the icon is shown in green color. Exiting the
NetCom Plus Manager by

button will not change this part

of the installation.

September 2016

NetCom Plus User Manual

Содержание NetCom Plus 111






































































































































Результаты поиска

Содержание NetCom Plus 111

Отзывы:

Похожие инструкции для NetCom Plus 111

Бренды по названию

Популярные бренды

VSCOM NetCom Plus 111, Руководство пользователя

Результаты поиска

Содержание NetCom Plus 111

Отзывы:

Похожие инструкции для NetCom Plus 111

Бренды по названию

Популярные бренды