voran EP 1000 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 40

voran EP 1000 Скачать руководство пользователя страница 23

De-stoning machine EP 1000

Version: 136401000_M0014772F_EN400/50D
Datum: 15.01.2021

- 23 / 40 -

5.2 Changing the screen

Picture 5.2-1)

Changing the screen

BEFORE OPENING UNPLUG!

Interrupting your work on the machine power supply and secure against accidental before
reconnecting it and turning.

Non compliance can mean severe personal injury.

1) The screen cover (Fig.Pos.2) can be removed when the two clasps (Fig.Pos.1) are opened.

2) Open the screw nuts (Fig.Pos.3) and the screws (Fig.Pos.4) in order to remove the bearing cover

(Fig.Pos.6)

3) The screen (Fig.Pos.7) can be pulled out downwards after screwing out the securing screw nut (Fig.Pos.5)

4) The machine is to be screwed back together again after the screen change has been completed.

5.3 Screen dimensions

The diameter of the screen holes depends on the type and the size of the fruit processed

➢

screen hole diameter 3mm. Cherries

➢

screen hole diameter 5mm. Plums

➢

screen hole diameter 8mm. peaches, apricots

«
...
21
22
23
24
25
...
»

Содержание EP 1000









































Отзывы:

Нет отзывов