voran EP 1000 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 40

voran EP 1000 Скачать руководство пользователя страница 12

De-stoning machine EP 1000

Version: 136401000_M0014772F_EN400/50D
Datum: 15.01.2021

- 12 / 40 -

1.8 Correct use

This machine/line is intended and constructed for the following use in full compliance with the contractual terms:

INFORMATION!

This machine may only be used for removing stones from core and stone
fruit.

Any other use of this machine/line represents an improper use of the machine/line.
The correct use of this machine/plant to terms of the contract requires further that the documentation/Operating
Manual as also the specified inspection and servicing intervals are strictly adhered to.

Although this machine/plant has been constructed to the highest technical standards and the recognised standards
of safety and has been accepted by the client, danger of injury or of loss of life may none-the-less arise for the user
or third persons as a result of its use, or the machine/line may itself be damaged.

The machine/line may only be operated when in a technically perfect condition, in a professional manner and when
the operator is fully aware of the safety and danger aspects.

Recognised weaknesses or faults that may reduce the safety of operation, must be dealt with in a professional
manner immediately or must be reported to customer service in a manner that can be proven!

1.9 Inappropriate use

WARNING AGAINST GENERAL DANGERS

Any use of this machine/line other than that as defined in the chapter "Correct Use", represents an
inappropriate use of the machine/line and can result in serious injuries of the operating staff or third
persons or to the damage or destruction of the line/machine.
The manufacturer/supplier cannot be held liable for any damage resulting from an inappropriate
use of the machine/line.

In such cases the user assumes full liability.

«
...
10
11
12
13
14
...
»

Содержание EP 1000









































Отзывы:

Нет отзывов