voran EP 1000 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 40

voran EP 1000 Скачать руководство пользователя страница 21

De-stoning machine EP 1000

Version: 136401000_M0014772F_EN400/50D
Datum: 15.01.2021

- 21 / 40 -

5

Operation

5.1 Operation of the Stone Removal Unit EP1000

Picture 5.1-1)

Operation

Switch on the machine at the star-delta switch (item no.2 in figure).
Move the switch to Y and then after 2

– 3 seconds move the switch further to the delta mark

By turning the starter in the other direction or pressing the emergency stop button, the device is switched off.

1) Connect the machine to the available power network (Fig. Pos.1).

2) Release emergency stop button (Fig. Pos.3) by turning.

3) Switch on the main switch (Fig. Pos.2).

4) Switch on the machine and check the direction of rotation. (Rotation direction arrow on strap protection

cover; make a visual check feed hopper top

→

worm screw direction of rotation).

5) It must be ensured that only fully ripe fruit that is processed.

6) When processing stone fruit it must be ensured that the fruit is cleaned, prepared with a grater and

conducted to a stone removal machine by a mash pump.

7) Without a mash pump the fruit is to be tipped into the feeder hopper as continuously as possible to prevent

motor overload.

8) The machine must continue to run until all the fruit is out of the machine before switching off.

«
...
19
20
21
22
23
...
»

Содержание EP 1000









































Отзывы:

Нет отзывов