voran EP 1000 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

voran EP 1000 Скачать руководство пользователя страница 15

De-stoning machine EP 1000

Version: 136401000_M0014772F_EN400/50D
Datum: 15.01.2021

- 15 / 40 -

3

Transportation and setting up of the machine/line

3.1 Notes on transportation

NOTE!

-  Before transporting the machine/line the motor is to be switched off and the
mains connector plug must be pulled out!
-  The machine/line must not be tipped!
-  In order to avoid transportation damage assemble any available
transport securing devices.
-  Secure the machine/line in an orderly manner on the means of transport!
-  Observe the statutory requirements (StVO) for legally specified dimensions
or mark the load!

Picture 3.1-1) Transportation De-stoning machine EP1000

F1 loading of the fork

250 kg

F2 foundation load

1100 N/m² or 110 kg/m²

1

transport pallet

2

Marker arrow for location points

WARNUNG VOR ALLGEMEINER GEFAHR

A forklift or crane with a lift capacity matched to the above table is necessary for unloading the
machine.

«
...
13
14
15
16
17
...
»

Содержание EP 1000









































Отзывы:

Нет отзывов