Von Duprin 98/9950WDC Скачать руководство пользователя

Страница: 14 / 16

BOTTOM LATCHBOLT CLEARANCE

Remove tape holding bottom bolt in place from bottom

of door.

For 2-Point Latch Only

Adjust bottom latchbolt clearance.

Pull

top spool screw

downward to release top

latch, if not already retracted.

Push

bottom latch pin

upward. Link will tilt.

For 2-Point Latch Only

b-1

b-2

b-3

Turn

bottom spool screw

clockwise approximately 20 turns to

remove slack. Continue turning until bolt just clears top of strike (b-4).

NOTE:

If clicking noises are heard during clockwise

adjustment, unwind the cable with one-half turn counter-
clockwise. Then, continue clockwise adjustment. If clicking
persists, check to be sure cable is not caught on an edge.

bolt

strike

b-4

³⁄₈

" standard

undercut

Perform bottom latch functional test.

For 2-Point Latch Only

c-1.

Confirm bottom latchbolt does not drag against floor when

door is opened.

c-2.

With door closed, bottom latch should be secure.

Содержание 98/9950WDC

















Результаты поиска

Содержание 98/9950WDC

Отзывы:

Похожие инструкции для 98/9950WDC

Бренды по названию

Популярные бренды

Von Duprin 98/9950WDC, Руководство по установке

Результаты поиска

Содержание 98/9950WDC

Отзывы:

Похожие инструкции для 98/9950WDC

Бренды по названию

Популярные бренды