Von Duprin 98/9950WDC Скачать руководство пользователя страница 16

Страница: 16 / 16

Printed in U.S.A.

24739468 Rev. 01/16-c

Customer Service

1-877-671-7011

www.allegion.com/us

TROUBLESHOOTING

If latches do not retract when pushpad is depressed:

Remove cover plate from edge of door

Pull down on

top spool screw

. If the top latch fails to actuate, readjust top spool (Steps 4d-1 thru 4d-4).

Pull up on

bottom spool screw

. If the bottom latch fails to actuate, readjust bottom latch clearance (Steps 8b-1 thru 8b-4).

If both actuate and the door is not functioning, proceed to next check.

Remove center case cover

Check

lift finger screws

to ensure they are still fully seated. If unseated, loosen

locking

screw

, and while applying pressure to the head of the

lift finger screw

seat it, tighten locking screw. If door is not functioning, proceed to next step.

With

both

lift finger screws

fully seated, loosen

top and bottom locking

screws

, turn

lift finger screws

clockwise to end of travel, and repeat

device adjustment, Step 6.

If bottom latch pin does not move during Step 6b-2:

Loosen

bottom spool screw

10 turns.

Seated

Unseated

Содержание 98/9950WDC

















Результаты поиска

Содержание 98/9950WDC

Отзывы:

Похожие инструкции для 98/9950WDC

Бренды по названию

Популярные бренды

Von Duprin 98/9950WDC, Руководство по установке

Результаты поиска

Содержание 98/9950WDC

Отзывы:

Похожие инструкции для 98/9950WDC

Бренды по названию

Популярные бренды