||
INSTRUMENTS AND CONTROLS
* Option/accessory.
166
indicator light will glow steadily or flash when the
button has been pressed. Activation will now
occur for the trained device (i.e., garage door
opener, gate operator, security system, entry door
lock, home/office lighting, etc.).
If the ignition is switched off, HomeLink will
function for 30 minutes after the driver's door
has been opened.
For convenience, the hand-held transmitter of the
device may also be used at any time.
In the event that there are still programming diffi-
culties or questions, contact HomeLink at:
www.HomeLink.com, www.youtube.com/
HomeLinkGentex or by phoning the hotline at 1–
800–355–3515.
Resetting HomeLink
®
buttons
Use the following procedure to reset (erase pro-
gramming) from the three HomeLink
®
buttons
(individual buttons cannot be reset but can be
“reprogrammed” as outlined in the following sec-
tion):
1. Press and hold HomeLink
®
buttons 1 and 3
for approx. 10 seconds until the indicator
light begins to flash green.
2. Release both buttons.
> HomeLink
®
is now in the training (or
learning) mode and can be programmed
at any time beginning with “To program
HomeLink
®
" above.
Reprogramming a single HomeLink
®
button
To reprogram an individual HomeLink
®
button:
1. Press and hold the desired HomeLink
®
but-
ton.
DO NOT
release the button.
2. The yellow indicator light will begin to flash
after 20 seconds. Without releasing the
HomeLink button, proceed with “To program
HomeLink
®
" step 1 above.
For questions or comments, contact HomeLink
at: www.HomeLink.com, www.youtube.com/
HomeLinkGentex or by phoning the hotline at 1–
800–355–3515.
FCC (USA) and IC (Canada)
This device complies with FCC rules part 15 and
Industry Canada RSS-210. Operation is subject
to the following two conditions: (1) This device
may not cause harmful interference, and (2) This
device must accept any interference that may be
received including interference that may cause
undesired operation. WARNING: The transmitter
has been tested and complies with FCC and IC
rules. Changes or modifications not expressly
approved by the party are prohibited.
The transmitter has been tested and complies
with FCC and IC rules. Changes or modifica-
tions not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the device.
15
Related information
•
15
The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications were met.
Содержание S 90 2017
