Volvo D12 Скачать руководство пользователя | Manualshive

Страница: 127 / 214

background image

Maintenance

123

Flushing Cooling System

Before filling, flush out the system thor-
oughly with clean water. Before flushing
out the radiator, remove the lower radiator
hose to allow a quicker and more efficient
draining.

When flushing the radiator, keep the water
pressure low so the radiator tubes are not
damaged.

W2003080

Filling Cooling System

Always use a pre-mixed solution of 50/50
clean water and antifreeze. Do not fill sys-
tem with water and then add antifreeze. A
mixture with less than 35% antifreeze does
not give adequate corrosion protection.
Concentrations of antifreeze above 60%
does not give added freeze protection. The
system is self-venting.

1

Fill the system with clean coolant
through the fill neck in the middle of
the surge tank. The fill rate is not to
exceed 2 gpm (8 L/min.). The engine
should not be running and the heater
control should be on WARM.

2

Fill up to the top of the surge tank.

3

Check the level after running the en-
gine at high idle for approximately
five minutes. Add coolant as required.

W2003082

W2003081

«
...
125
126
127
128
129
...
»

Содержание D12























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D12

Бренд: ULPOWER Страницы: 20

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Бренд: Nord Drivesystems Страницы: 112

Бренд: Engine distributors Страницы: 331

Бренд: Tanaka Страницы: 10

Бренд: Briggs & Stratton Страницы: 12

Бренд: Yamaha Страницы: 25

Бренд: Yamaha Страницы: 18

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 62

Бренд: Yamaha Страницы: 59

Бренд: Yamaha Страницы: 64

Бренд: Yamaha Страницы: 66

Бренд: Yamaha Страницы: 66

TRANSERVO SSC04

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 104

Бренд: Yamaha Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды