Volvo D12 Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 214

background image

144

Maintenance

Brake Safety Information

The brake system is a critical vehicle
safety system. For your safety and for
those around you, follow the recom-
mended preventive maintenance checks.
If any problems occur, have them inves-
tigated immediately by an authorized
service facility. Failure to properly main-
tain the brake system can result in
compromised brake efficiency and may
lead to loss of control of the vehicle re-
sulting in severe personal injury or death.

Do not use replacement parts anywhere
in the brake system unless it conforms
exactly to original specifications. A non-
conforming part in your vehicle’s brake
system could cause a malfunction, lead-
ing to loss of control of the vehicle
resulting in severe personal injury or
death.

Do not release the parking brake or at-
tempt to move the vehicle until brake air
pressure in both circuits is at least 100
psi (690 kPa). Failure to follow this pro-
cedure may lead to uncontrolled vehicle
movement and cause severe personal in-
jury or death.

Drain the air system tanks at the recom-
mended intervals. If condensation
accumulates, moisture can enter the
brake system air valves, causing corro-
sion or clogging. The safety of the brake
system could be compromised, leading
to an accident causing severe personal
injury or death.

Do not inspect or adjust parts or compo-
nents in the brake system without setting
the parking brake, placing the transmis-
sion in neutral and securely chocking the
wheels. If the vehicle is not secured to
prevent uncontrolled vehicle movement,
it could roll and cause severe personal
injury or death.

WARNING

Do not use penetrating oil, brake fluid or
wax-based oils in the air system. These
fluids may cause severe damage to air
system components.

«
...
146
147
148
149
150
...
»

Содержание D12























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D12

Бренд: Perkins Страницы: 92

Бренд: Stobag Страницы: 40

Бренд: Wacker Neuson Страницы: 114

Бренд: Jula Страницы: 17

Бренд: Sanshin Страницы: 25

Бренд: Barrus Страницы: 97

Yanmar 3TVN 88C-KHW

Бренд: HAKO Страницы: 36

Бренд: SPE Страницы: 7

Бренд: TEM Страницы: 19

75-200 V DC Series

Бренд: TEM Страницы: 38

Бренд: TEM Страницы: 42

Бренд: Volvo Страницы: 25

Бренд: CAME Страницы: 64

Бренд: Valach Motors Страницы: 3

TUBULAR 35 Series

Бренд: Delton Страницы: 3

Бренд: MULTIPLEX modell Страницы: 11

Бренд: Honda Страницы: 86

Бренд: O.S. engine Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды