Volvo D12 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 214

background image

Maintenance

127

Cleaning Charge-Air-Cooler and Radiator Package

Over time, dirt and insects will accumulate
between the fins of the radiator, air condi-
tioning condenser and charge-air-cooler.
The reduced air flow reduces the heat trans-
fer from the components to the air. This
increases the load on the fan and air condi-
tioning compressor and can result in engine
overheating and other performance related
problems, such as high fuel consumption,
etc. Make sure the radiator/charge-air-
cooler package is inspected regularly. Clean
if necessary.

Before working on or inspecting a vehi-
cle, set the parking brakes, place the
transmission in neutral and block the
wheels. Failure to do so can result in un-
expected vehicle movement and can
cause serious personal injury or death.

WARNING

Always wear eye protection when clean-
ing radiator, charge-air-cooler and
condenser. Failure to follow this recom-
mendation may result in eye injury.

The simplest method to clean the package
is to use air pressure or a water stream.
This should be done from the back of the
core. Air pressure should not exceed 30 psi
(200 kPa) for radiator and charge-air-cooler
cores. The use of a fin comb is also a good
tool to loosen bugs and dirt from the fins.

If dirt can not be cleaned off with this pro-
cedure, consult your Volvo Truck dealer.

Inspect the charge-air-cooler for cracks at
every inspection. Do not operate the vehicle
with a damaged or broken charge-air-
cooler. To do so would void the warranty
and the engine will not meet emission regu-
lation requirements.

W2001496

«
...
129
130
131
132
133
...
»

Содержание D12























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D12

Бренд: M+S Страницы: 6

Бренд: Yanmar Страницы: 100

Бренд: ebm-papst Страницы: 9

Бренд: SCREENLINE Страницы: 4

GARDEN SNOWBUSTER (160F)

Бренд: Texas Страницы: 33

Бренд: York Страницы: 40

Бренд: Vetus Страницы: 28

Low Voltage Motors EQPIII-841

Бренд: Toshiba Страницы: 2

Low Voltage Motors VR Series

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 18

Бренд: Toshiba Страницы: 31

Бренд: Toshiba Страницы: 49

Бренд: Yamakoyo Страницы: 41

Бренд: Volvo Страницы: 72

Бренд: Robin America Страницы: 78

Бренд: Detroit Diesel Страницы: 42

Бренд: MULTIPLEX modell Страницы: 11

Бренд: Honda Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды