Volvo D12 Скачать руководство пользователя | Manualshive

Страница: 151 / 214

background image

Maintenance

147

Check Valves

Before working on or inspecting the ve-
hicle, set the parking brakes, place the
transmission in neutral and block the
wheels. Failure to do so can result in un-
expected vehicle movement and can
cause serious personal injury or death.

Follow the procedure below to check out
the air tank check valves at least once a
year. This is to see if air pressure is main-
tained in the tanks when the air pressure is
depleted in the supply tank (wet tank).

NOTE! The check valves should be
checked at least once per year.

1

Chock the rear wheels.

2

Let the compressor build up air pres-
sure to the governor cut-off.

3

Bleed the air pressure from the supply
tank (wet tank).

4

Check the air pressure gauges on the
instrument panel to see if the pressure
is maintained in both primary and sec-
ondary air tanks.

5

Any bleed-off from one or both of the
tanks indicates a defective check
valve; replace valve.

6

Repressurize the system and remove
the wheel chocks.

WARNING

To prevent personal injury, always drain
the air supply from the vehicle before
attempting to repair or replace a compo-
nent. Wear eye protection and take care
not to get fingers caught in the slack ad-
justers when spring brakes are applied.

Compressed air components can separate
violently during disassembly if air pres-
sure is present. Before servicing any part
of the brake air system, completely re-
lease the air pressure. Failure to do so
can result in serious personal injury or
death.

«
...
149
150
151
152
153
...
»

Содержание D12























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D12

Бренд: BAFANG Страницы: 5

Бренд: RHINO MOTION CONTROLS Страницы: 4

Бренд: Ofna Racing Страницы: 2

Бренд: Briggs & Stratton Страницы: 10

Бренд: Suzuki Страницы: 91

Бренд: Sanshin Страницы: 25

Бренд: Parker Страницы: 32

Бренд: Saito Страницы: 27

Бренд: Yanmar Страницы: 52

Бренд: Mercedes-Benz Страницы: 324

Dexxo Pro 1000 RTS

Бренд: SOMFY Страницы: 13

Elixo 500 230 V

Бренд: SOMFY Страницы: 44

Elixo 500 230 V

Бренд: SOMFY Страницы: 48

HYDRO-FORCE 65043

Бренд: Bestway Страницы: 8

Бренд: Volvo Penta Страницы: 1

Бренд: Volvo Penta Страницы: 15

Бренд: Volvo Penta Страницы: 76

Бренд: Volvo Penta Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды