Volvo D12 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 214

background image

Safety Information

3

Proper Maintenance Procedure

During Maintenance

Whenever performing maintenance or re-
pair, attach a DO NOT OPERATE or
similar warning label or sign to the ignition
key or prominently displayed on the instru-
ment panel.

Do not allow unauthorized personnel on,
around or in the vehicle when mainte-
nance or repair is being performed.

WARNING

Do not attempt to repair or service this
vehicle without having sufficient train-
ing, correct service literature and the
proper tools. Failure to follow this could
lead to personal injury or making your
vehicle unsafe.

WARNING

Diesel engine exhaust and some of its
constituents are known to the state of
California to cause cancer, birth defects
and other reproductive harm.

•

When operating the engine in an en-
closed area, vent the exhaust to the
outside.

Exhaust gases contain carbon monoxide.
Always run the engine outdoors or use a
properly vented exhaust hose. Prolonged
or excessive exposure may cause serious
illness or death.

•

Before servicing your vehicle, apply
the parking brakes and adequately
chock the wheels in order to prevent
unintended vehicle movement. If the
service procedure requires the parking
brakes to be released — recheck to en-
sure that the wheels are adequately
chocked to prevent all forward and/or
rearward movement.

•

Do not use combustible substances in
or around the engine either during re-
pair or maintenance or when running
the engine.

Never operate the engine in an area
where hydrocarbon vapors (gasoline, for
example) are present or are suspected to
be present. Hydrocarbon vapors can en-
ter the air intake and overspeed the
engine, causing severe engine damage
and/or an explosion and fire. Serious
personal injury or death could occur.

•

Do not wear loose clothing or jewelry
that can catch or get snagged by parts
or moving components on the engine.
Also wear all protective equipment re-
quired by the job conditions, such as
protective glasses, hearing protection,
etc.

•

Make certain that all protective covers
and guards are in place and secured.

•

Never put maintenance fluids into
glass containers since glass containers
can break.

«
...
5
6
7
8
9
...
»

Содержание D12























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D12

Бренд: Parker Страницы: 36

Бренд: HunterDouglas Страницы: 20

Xcelorin LOSB9400 3.5T

Бренд: Team Losi Страницы: 4

Бренд: YOODA Страницы: 7

Бренд: Motorola Страницы: 82

24 v High Performance Synchronous Motor

Бренд: Rega Страницы: 1

Бренд: AL-KO Страницы: 132

Бренд: cemp Страницы: 18

Бренд: Lycoming Страницы: 84

Бренд: RADEMACHER Страницы: 72

Бренд: LRP Страницы: 4

Бренд: Yanmar Страницы: 35

Бренд: Yanmar Страницы: 164

Бренд: Yanmar Страницы: 33

Бренд: Honda Страницы: 31

Бренд: O.S. engine Страницы: 18

Бренд: Grundfos Страницы: 12

Nitro Star T-15

Бренд: HPI Racing Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды