Volvo Penta D7A T Скачать руководство пользователя страница 66

Страница: 66 / 116

Fuel filter, Change

Clean the filter bracket and place a receptacle under
the filters.

NOTICE!

Leave the old filters to a destruction plant.

Single fuel filter

1 Close the fuel supply to the engine.

2 Unscrew the filter.

3 Make sure the new filter are absolutely clean and

that the gasket undamaged. Lightly moisten the
gasket with oil.

4 Screw on the filters by hand until they make contact

with the sealing surface. Then screw a further half
turn, not any more!

5 Open the fuel supply.

6 Bleed the fuel system as described above.

7 Start the engine and make sure there are no leaks.

Dual fuel filters

WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and hot
surfaces.

1 Place a receptacle beneath the filters and carefully

clean the filter bracket.

2 Put the lever (2) in its right-hand end position.

3 Unscrew the left-hand fuel filter and discard it. Use

a filter wrench if necessary.

4 Screw on the new filter by hand until the gasket

make contact with the sealing surface. Then tighten
a further half turn, not any more!

5 Open the left-hand bleed screw (1) on the filter

bracket. Put the lever in operating position (straight
up). Close the bleed screw when the fuel running
out is free from air.

6 Put the lever in its left-hand end position and

change the right-hand fuel filter in the same way.

Maintenance

47713337 03-2021 © AB VOLVO PENTA

Содержание D7A T





















































































































Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды

Volvo Penta D7A T, Руководство оператора

Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды