Volvo Penta D7A T Скачать руководство пользователя страница 64

Страница: 64 / 116

Fuel System

WARNING!

Fire hazard. When carrying out work on the fuel system
make sure the engine is cold. A fuel spill onto a hot
surface or an electrical component can cause a fire.
Store fuel soaked rags so that they cannot cause fire.

IMPORTANT!

Only use the grades of fuel

recommended in the fuel specification below, refer to

Technical Data, Fuel System

. Always observe the

greatest cleanliness during re-fueling and work on the
fuel system.

IMPORTANT!

All work on the engine injection system must be done
by an authorized workshop.

Bleeding the Fuel System

The fuel system must be bled, e.g. after changing fuel
filter, if the fuel tank has been run dry and after long
stops.

1 Put a suitable vessel under the fuel return (1).

2 Loosen the bolt.

3 Turn the engine over with the starter (max. 20 sec.)

until fuel free of bubbles comes out.

4 Tighten the bolt.

5 Start the engine and make sure there are no leaks.

IMPORTANT!

Do not loosen the injector delivery pipes. If the delivery
pipes are loose they must be changed.

P0002101

P0003697

Maintenance

47713337 03-2021 © AB VOLVO PENTA

Содержание D7A T





















































































































Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды

Volvo Penta D7A T, Руководство оператора

Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды