Volvo Penta D7A T Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 116

background image

Before any work on the cooling system

WARNING!

Stop the engine and let it cool before starting work on
the cooling system. Hot fluids and hot surfaces can
cause burns.

Risk of water penetration/sinking

WARNING!

If a launched boat is equipped with sea water tap and
safety valve,

ensure that these are closed

before any

work is allowed to begin on the cooling system.
Remember to open the tap and valve before starting
the engine!

Hot oil under pressure

CAUTION!

Hot oil can cause burns. Avoid getting hot oil on the
skin. Ensure that the lubrication system is not
pressurized before starting any work. Never start or
operate the engine without the oil filler cap is on. There
is a risk that hot oil can spray out.

Refueling

WARNING!

There is always a risk of fire and explosion during
refueling. Smoking is forbidden and the engine must
be stopped.

Proper fuel quality

IMPORTANT:

Always use the fuel recommended by Volvo Penta.
See

Technical Data

in Operator’s Manual. Other fuel

can damage the engine.
Wrong fuel quality can also lead to higher service
costs.

WARNING!

Risk of personal injury.
Wrong fuel quality in a diesel engine can cause the fuel
control mechanism to bind which can cause the engine
to overspeed!

Legal requirements to use proper fuel

IMPORTANT:

To meet regulatory requirements for certified emission
levels must always recommended fuel according to

Technical Data

in the Operator’s Manual be used.

P0024484

P0024477

Safety Information

47713337 03-2021 © AB VOLVO PENTA

9

«
...
9
10
11
12
13
...
»

Содержание D7A T





















































































































Отзывы:

Нет отзывов

Похожие инструкции для D7A T

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 96

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

PowerXL DX-NET-ETHERCAT-2

Бренд: Eaton Страницы: 3

Бренд: Oldham Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды