Volvo Penta D7A T Скачать руководство пользователя страница 32

Страница: 32 / 116

In Case of Emergency

Starting Using Auxiliary
Batteries

WARNING!

Explosion hazard. Batteries contain and give off an
explosive gas which is highly flammable and explosive.
A short circuit, open flame or spark could cause a
violent explosion. Ventilate well.

WARNING!

Never confuse the positive and negative poles on the
batteries. Risk of arcing and explosion.

1 Check that the auxiliary battery has the same

voltage as the engine system voltage.

2 Connect the red positive cable to the plus (+)

terminal on the discharged battery and then to the
plus terminal on the auxiliary battery.

3 Connect the black start cable to the minus (–)

terminal on the auxiliary battery and to a place a
little distance away from the discharged battery,
e.g. the start motor's negative terminal.

WARNING!

The black jumper cable (–) must never come in contact
with the positive connection on the starter motor.

4 Start the engine and let it run at fast idle for

approximately 10 minutes to charge the batteries.
Make sure there is no extra equipment connected
to the electrical system.

WARNING!

Working with or approaching a running engine is a
safety risk. Watch out for rotating components and hot
surfaces.

WARNING!

Do not touch the connections during the start attempt:
Risk of arcing.
Do not bend over any of the batteries either.

5 Turn off the engine. Remove the start cables in the

exact opposite order to their connection.

47713337 03-2021 © AB VOLVO PENTA

Содержание D7A T





















































































































Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды

Volvo Penta D7A T, Руководство оператора

Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды