Volvo Penta D7A T Скачать руководство пользователя страница 63

Страница: 63 / 116

Oil filter, Change

Change the oil filter every second oil change.

1 Drain the oil, see

Engine Oil, Change, page 60

2 Put a vessel underneath the filter to avoid oil spill.

3 Unscrew the oil filters with a suitable filter wrench.

4 Lightly oil the rubber seal of the new filters and

make sure its mating surfaces on the filter brackets
are clean.

5 Screw on the filter by hand until the rubber gasket

just touches the filter holder sealing surface. Then
tighten the filter a further 3/4 to 1 turn.

6 Fill up with oil , refer to

Oil level, checking and

topping up

7 Start the engine (idle) and make sure that no

leakages occur. Check the oil level once the engine
has stopped.

Oil Level, Check

The oil level must be within the marked range on the
dipstick and should be checked daily.

Engine Oil, Filling

Top up the oil through the filler opening in the
ventilation cover. Make sure the correct level is
attained but wait a few minutes to allow the oil to run
into the oil sump.

WARNING!

Hot oil and hot surfaces can cause burns.

IMPORTANT!

Do not fill above the maximum oil level. Use only oil of
the recommended grade (refer to chapter

Technical

Data, page 102

Maintenance

47713337 03-2021 © AB VOLVO PENTA

Содержание D7A T





















































































































Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды

Volvo Penta D7A T, Руководство оператора

Результаты поиска

Содержание D7A T

Отзывы:

Похожие инструкции для D7A T

Бренды по названию

Популярные бренды