5
ENGLISH
if they are not instructed by this person on the
usage of the unit.
•
For children safety reasons do not leave poly-
ethylene bags used as a packaging unattended.
•
Attention!
Do not allow children to play with
polyethylene bags or packaging film.
Danger
of suffocation!
•
Check the power cord and plug periodically. Do
not use the unit if its body, power plug or power
cord is damaged.
•
To avoid damages, transport the unit in the origi-
nal package only.
•
Do not use the unit if the power cord or plug is
damaged, if the unit malfunctions, after the unit
was dropped or damaged in any other way.
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction is
detected or after it was dropped, unplug the unit
and apply to any authorized service center from
the contact address list given in the warranty
certificate and on the website www.vitek.ru.
•
Keep the unit out of reach of children.
THIS UNIT IS INTENDED FOR HOUSEHOLD USAGE
ONLY
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
•
Unpack the unit and remove any stickers that
can prevent unit operation.
•
Check the unit for damages; do not use it in case
of damages.
•
Before switching the unit on, make sure that
voltage of the mains corresponds to unit operat-
ing voltage and the switch (6) is set to the posi-
tion «
OFF
» (switched off).
•
Clean the unit body with a damp cloth and then
wipe it dry.
•
Wash all removable parts with warm water and
neutral detergent, then rinse and dry thoroughly
before assembling.
OPERATION MODE SWITCH
The marks on the switch (6) correspond to the fol-
lowing operation modes:
«
OFF» –
the meat grinder is off, the middle posi-
tion of the switch.
«
ON»
– the meat grinder is on, the fixed position
of the switch.
«
R
» – reverse mode, the switch position is not
fixed.
ATTENTION!
•
The meat grinder is intended to mince boneless
meat for household use only.
•
Before grinding meat, make sure that meat is
fully defrosted, all bones and excess fat are
removed. Cut meat into small pieces (no more
than 2 cm x 2 cm x 6 cm), so they can fit easily
into the food tray (2) opening.
•
Place the unit on a flat dry surface.
•
Make sure that ventilation openings on the unit
body are not blocked.
•
Do not push the products with any foreign
objects or your fingers, use only the pusher (1)
supplied with the unit for pushing the products
through.
•
Never immerse the meat grinder body, the
power plug or the power cord into water or other
liquids.
•
Do not try to process food with hard fiber (for
example, ginger, horseradish or nuts) in the
meat grinder.
•
To avoid obstructions, do not apply excessive
force while pushing meat with the pusher (1).
•
If any hard piece of food stops the feeder screw
or cutting blade rotation, immediately switch the
unit off by setting the switch (6) to the “
OFF
”
(off) position and use the screw reverse mode
«R
» (reverse) to remove the obstruction before
starting again. To do this press and hold the
switch (6) in the position “
R
” for several sec-
onds.
Attention!
–
Before switching the meat grinder from
«ON» mode to «R» mode and back, switch it
off and make sure that all the rotating parts
of the meat grinder stopped or wait at least
30 seconds.
•
Do not run the unit for more than 10 minutes con-
tinuously when processing the food products.
•
After 10 minutes of continuous use, switch the
meat grinder off and let it cool down during
10-15 minutes before further operation.
•
After you finish operating, switch the meat
grinder off, setting the switch (6) to the position
«
OFF
» (off) and unplug the unit; after that you
can disassemble it.
MEAT PROCESSING
1.
Press and hold the meat grinder head lock but-
ton (5).
2.
Match the grooves on the meat grinder head (3)
with the ledges on the installation place (4)
(pic. 1).
IM VT-3614.indd 5
30.08.2016 11:17:40
