Vitek VT-2340, Инструкция по эксплуатации

Страница: 4 / 32

4
ENGLISH
•
Do not attempt to repair the unit. Do not disas-
semble the unit by yourself, if any malfunction
is detected or after it was dropped, unplug
the unit and apply to any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE IN
PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature.
There may be water spots in the air humidi-
fier, this is normal, as the unit has undergone
quality control.
–
Unpack the air humidifier, remove packaging
materials and any promo-stickers that can
prevent the unit operation. Check the unit for
damages. Do not switch the air humidifier on
in case of damages.
–
Before plugging the unit in make sure that
your home mains voltage corresponds to the
unit operating voltage.
Notes:
–
use the humidifier at the room temperature
from +10°С to +40°С, and relative humidity
less than 80%.
–
water temperature should not 40°С.
USING THE AIR HUMIDIFIER
Notes:
–
the operation mode selection and setting
buttons are sensory, you just need to touch
the button to switch the necessary operation
mode on, every touch of the active button is
accompanied by a sound signal.
–
Remove the nozzle (1).
–
Take the water tank (3) by the handle (2) and
remove it from the unit body (9).
–
Turn over the tank (3), open the lid (5) rotating
it counterclockwise.
–
Fill the tank (3) with necessary amount of
water, insert the lid (5) into the water inlet and
screw it in clockwise.
–
First place the filled water tank (3) back to its
place and then install the nozzle (1).
–
Wait for some time until the process cham-
ber (7) is filled with water.
Note:
–
before the first use it is recommended to put
the mineral filter (4) into a container filled with
water of room temperature for several min-
utes.
–
remove the filter (4) from the lid (5) turning it
counterclockwise, put the filter (4) into a con-
tainer filled with water for several minutes,
take the filter out of the water and drain the
remaining water, then install it back on the lid
(5), and turn it clockwise.
–
Insert the plug into the socket, you will hear
a sound signal
.
–
Switch the unit on by touching the button
“
ON/OFF” (13), you will hear a sound
signal and the digital symbols will show the
room temperature (10) and relative humid-
ity (11). The unit will be switched on at the
medium “mist” release intensity, the operat-
ing modes are confirmed with the symbols in
the icon row (12) on the control and indica-
tion panel (6).
–
To switch the air humidifier off touch the but-
ton (13) again.
–
Unplug the unit.
Notes:
–
the humidity level and temperature readings
may be slightly different from the readings of
another hygrometer and thermometer.
–
the humidity level readings depend on the
room air temperature.
–
draughts or other air flows may significantly
affect the air humidity and temperature read-
ings in the room.
OPERATION MODE CONTROL BUTTONS
«
ON/OFF» button (13)
–
Touch the button (13) to switch the unit on, the
symbol
« » will appear in the icon row (12)
on the panel (6). To switch the unit off, touch
the button
« ON/OFF» » (13) again.
« MIST» button (16)
–
Consequently pressing the button “ MIST”
(16) you can select the “mist” release inten-
sity, the “mist” release intensity is shown with
scrolling symbols in the icon row (12) on the
panel (6).
IM VT-2340.indd 4 18.01.2019 10:20:55