Vision Research Phantom Flex4K Скачать руководство пользователя страница 31

Страница: 31 / 94

Chapter 4: On-Camera Controls

Press ‘Playback’ button to start playback of last take
(whether in RAM or Phantom CineMag IV).

Tap the ‘Return’ button to access previous screen.

Tap ‘Trigger’ button to jump to ‘Home’ menu. The video
will return to ‘Live’ state, unless multi-cine (partitions)
are in use.

Press button to define a new start point of the selected
RAM cine. A long press re-sets the in point.

Press to save the RAM cine to an installed CineMag IV.
Also displays the CineMag save progress.

Press button to define a new end point of the selected
cine. A long press resets the out point.

Press to play selected cine in reverse; long press to
fast reverse; longer press to increase reverse speed;
tap to pause.

Press button then Rotate the control knob to cycle
through available cines in RAM or CineMag IV.

Press to play selected cine; long press to fast forward;
longer press to increase fast forward speed; tap to
pause.

The Control knob also allows you to quickly scrub
through the selected Cine, and fine-tune the mark-in
and mark-out position. Scroll forward to play forward,
the further you scroll the faster the playback - same in
reverse.

Single frame stepping is also possible with the control
knob. In playback mode, tap the knob to switch
between single frame and 2% scrub increments.

Mark In

Save

Mark Out

Reverse

Cine Select

Play forward

Navigation

Control knob

Содержание Phantom Flex4K































































































Результаты поиска

Содержание Phantom Flex4K

Отзывы:

Похожие инструкции для Phantom Flex4K

Бренды по названию

Популярные бренды

Vision Research Phantom Flex4K, Руководство пользователя

Результаты поиска

Содержание Phantom Flex4K

Отзывы:

Похожие инструкции для Phantom Flex4K

Бренды по названию

Популярные бренды