VIPColor VP6 Series страница 74 Скачать руководство пользователя | Manualshive

Страница: 74 / 84

background image

74

Appendix

Additional Networking Information

If the Printer Has a Static IP Address

DHCP is enabled by default. If DHCP is not available and the printer is assigned a
static IP address, set the static IP address from the control panel before installing the
printer driver.
1. Press

(

Config

) on the control panel to access the configuration menus.

2. Level 2 security is required to change network settings (see

Selecting the Security

3. Scroll to the

NETWORK

menu to make the changes:

4. Connect the printer to the network.
5. Insert the printer setup disc into the computer’s disc drive to continue with the

printer driver installation for a network printer.

If the Connection to the Printer Has Changed

If the printer has been set up using a USB connection and is later connected via the
network (or vice versa), reinstall the printer driver.
1. Network – Connect the printer to the network.

USB – Do not connect the printer at this point. You will be prompted to do so
during the driver setup.

2. Insert the printer setup disc into the computer’s disc drive. Select the option

Add

another printer

.

3. Follow the instructions to complete the installation.

DHCP Setting

Set to Manual.

IP Settings

Enter the static IP settings for the printer.
• Static IP
• Subnet Mask
• Gateway
• WINS Server
a. Press

and

to set each digit (0 to 9).

b. Press

to move to the next digit.

«
...
72
73
74
75
76
...
»

Содержание VP6 Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для VP6 Series

Бренд: iFactory3D Страницы: 39

Бренд: Datamax Страницы: 2

WORKCENTRE 5050

Бренд: Xerox Страницы: 186

7500DX - Phaser Color LED Printer

Бренд: Xerox Страницы: 5

Бренд: Zebronics Страницы: 6

Бренд: Roland Страницы: 36

Бренд: U-Line Страницы: 33

Бренд: Mitsubishi Страницы: 2

5470 - X Color Inkjet

Бренд: Lexmark Страницы: 202

Бренд: Xerox Страницы: 244

Бренд: iDPRT Страницы: 41

Бренд: Kyocera Страницы: 16

Бренд: Loadrite Страницы: 12

Бренд: Infinite Peripherals Страницы: 35

Бренд: Konica Minolta Страницы: 150

Бренд: MF DIGITAL Страницы: 9

Бренд: Sunso Страницы: 27

Бренд: 2connet Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды