VIPColor VP6 Series страница 18 Скачать руководство пользователя | Manualshive

Страница: 18 / 84

background image

18

Using the Printer

Printing Labels

The printer is ready to print when the control panel displays

Printer Online

.

1. Select the

Print

command from your application.

2. Select the printer and click the

Setup

,

Properties

or similar button.

The print settings displayed are the defaults that were set in the printer driver.

3. Change the print settings if needed.

NOTE:

Ensure the media settings (e.g. label size) match the media loaded in the
printer.

4. Print the document.
Any changes to the settings only apply to the current print job. Once you exit the
application, the changes may be lost. Make the changes in the printer driver if you
wish to keep the settings as the default for all print jobs.

Change Default Settings in Printer Driver

To select the default print settings that will be used for all print jobs:
1. From the Windows

Start

menu, select

Devices and Printers

1

.

2. Right-click the printer, and select

Printing preferences

.

3. Make the changes (see

) and click

OK

to save.

1. For Windows 7. The steps will differ for other Windows versions.

«
...
16
17
18
19
20
...
»

Содержание VP6 Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для VP6 Series

Бренд: NCR Страницы: 10

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 36

Color imageCLASS MF8580Cdw

Бренд: Canon Страницы: 20

Color imageCLASS MF8280Cw

Бренд: Canon Страницы: 24

Color imageCLASS MF8080Cw

Бренд: Canon Страницы: 39

Color imageCLASS MF8050Cn

Бренд: Canon Страницы: 32

Color imageCLASS LBP7660Cdn

Бренд: Canon Страницы: 2

Color imageCLASS 8180c

Бренд: Canon Страницы: 24

Бренд: Canon Страницы: 30

C3000 - MultiPASS Color Inkjet Printer

Бренд: Canon Страницы: 41

Color imageCLASS MF8170c

Бренд: Canon Страницы: 2

Color imageCLASS MF8170c

Бренд: Canon Страницы: 98

Color imageCLASS MF8170c

Бренд: Canon Страницы: 8

Color imageCLASS MF8080Cw

Бренд: Canon Страницы: 46

Color imageRUNNER LBP5360

Бренд: Canon Страницы: 3

PIXMA MX882 Series

Бренд: Canon Страницы: 34

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 913

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды