Viola Systems Arctic Substation Gateway Скачать руководство пользователя

Страница: 43 / 51

User Manual
Arctic Substation Gateway

Firmware Version 2.4.x

Document Version 1

frames and restarts the IEC-101 link if the test fails. The events are still not
polled before the IEC-104 connection is active.

Table 42: IEC-101 keep link open

IEC-101 keep link open

Type

Boolean

Units

N/A

Value
range

No, Yes

Note

Some IEC-101 slaves require the link to be continuously open in order to
operate.

Reply header timeout
Defines the timeout Arctic waits the reply to start from IEC-101 slave after
command or request.

Table 43: IEC-101 reply start timeout

IEC-101 reply start timeout

Type

Timeout

Units

Milliseconds

Value range

1-65000

Note

Reply end timeout
Defines the maximum duration of IEC-101 slave response.

Table 44: IEC-101 reply end timeout

IEC-101 reply end timeout

Type

Timeout

Units

Seconds

Value range

1-65000

Note

Retry limit
Defines the number of retries sent to a IEC-101 slave in case of no reply. If no
reply is still received the Arctic closes the IEC-101 and IEC-104 connections.

Table 45: IEC-101 retry limit

IEC-101 retry limit

Type

Retry limit

Units

Retries

Содержание Arctic Substation Gateway




















































Результаты поиска

Содержание Arctic Substation Gateway

Отзывы:

Похожие инструкции для Arctic Substation Gateway

Бренды по названию

Популярные бренды

Viola Systems Arctic Substation Gateway, Руководство пользователя

Результаты поиска

Содержание Arctic Substation Gateway

Отзывы:

Похожие инструкции для Arctic Substation Gateway

Бренды по названию

Популярные бренды