Viola Systems Arctic Substation Gateway Скачать руководство пользователя

Страница: 10 / 51

User Manual
Arctic Substation Gateway

Firmware Version 2.4.x

Document Version 1

2 Hardware description

This section describes the physical interfaces on Arctic Substation Gateway.

2.1

Front panel

Arctic Substation Gateway front panel is shown in the figure below.

Figure 1. Front Panel

LEDs and switches (from left to right) with section reference to more detailed
information:

1. Reset button (

Power switch and reset button

on page 16)

2. Error LED (section

LEDs

on page 11)

3. Ethernet WAN port (section

Ethernet WAN

on page 12)

4. Ethernet LAN ports (section

Ethernet LAN

)

5. LEDs (section

LEDs

on page 11)

6. Serial console port (section

Serial console port

on page 13)

7. SIM card slots (section

SIM card slots

on page 16)

2.2

Back Panel

Arctic Substation Gateway back panel is shown in the figure below.

Figure 2. Back Panel

Connectors (from left to right):

Содержание Arctic Substation Gateway




















































Результаты поиска

Содержание Arctic Substation Gateway

Отзывы:

Похожие инструкции для Arctic Substation Gateway

Бренды по названию

Популярные бренды

Viola Systems Arctic Substation Gateway, Руководство пользователя

Результаты поиска

Содержание Arctic Substation Gateway

Отзывы:

Похожие инструкции для Arctic Substation Gateway

Бренды по названию

Популярные бренды