Vingtor Stentofon AlphaCom XE Series Скачать руководство пользователя

Страница: 15 / 68

AlphaCom XE - Installation, Configuration & Operation

A100K10805

The board provides 6 remote control software controlled outputs.
The line monitoring option requires a 10K resistor across the line at the

telephone end. The monitoring reports errors on all subscriber lines. If

the handset is left off-hook for 1 hour (programmable timer), a line error

is reported.
There are jumpers on the board to select options. The default settings

should normally not be changed.

● Line feed voltage

48 V

Default, normally used

24 V

Short distance or special 24 V phones

● Ringing voltage for each station

Internal

Default, for indoor or office environment

External

For outdoor or industrial environments

or for many telephones on one line

● Line balance

Complex

Default, normal in most countries

600 ohm

Best in some countries,

may reduce feedback in handset

AlphaCom XE20/XE26

Telephones and control outputs are connected to a connection board

mounted on the server connection field.
Telephone connection boards with transient protection (100 9930 202)

and subscriber connection cables with filter board (100 9501 031) must

be purchased separately.
Telephones may also be connected to an LCM board (100 9950 100).

This board is likely to be installed in XE servers with DTMF telephones

due to the expanded capacity. The default DIP switch settings should

normally not be changed.
The first and last three connector pairs on each board shall not be used.

AlphaCom XE7

All telephones are connected by means of pluggable screw terminals on

the server backplane.
The ALTB board can be placed in any board position 1-6. The example

drawing shows an ATLB board in position 2. If possible, avoid using

boards in position 1 as connection points 5 and 6 are used for program

input by default.
Further information on the ATLB board is found in datasheet

A100K10237.

2.2.11 ATLB-12 - Telephone Line Board

ATLB-12 has the same functions as ATLB except that it has 12 two-wire

DTMF telephone lines. ATLB-12 does not support line monitoring.
The 6 first telephones get the physical number according to the card’s

physical slot and the last 6 telephones have numbers with an offset of

+276 to the 6 first physical numbers.
This board is likely to be installed in XE servers with DTMF telephones

due to the expanded capacity.
The default DIP switch settings should normally not be changed.
See separate LCM documentation for more information.

AlphaCom XE20/XE26

The ATLB-12 boards are connected to the LCM via 1.5 m (100 9501

011) or 3.0 m (100 9501 014) connection cables, one for each board.

RING1

TIP1

RING2

TIP2

RING3

TIP3

RING4

TIP4

RING5

TIP5

RING6

TIP6

G123456G

RCO

CONNECTION BOARD

TX RX G

MRBD

1 . . . . 6

Relay board

1K+

1K-

2K+

2K-

3K+

3K-

4K+

4K-

5K+

5K-

6K+

6K-

S6
S5
S4
S3
S2
S1

RCO 6

RCO 5

RCO 3

RCO 4

RCO 2

RCO 1

Physical no.

Line board 1

1 0

Phys. no.

1K+

1K-

2K+

2K-

3K+

3K-

4K+

4K-

5K+

5K-

6K+

6K-

S6
S5
S4
S3
S2
S1

277

279

281

278

280

282

RCO 6

RCO 5

RCO 3

RCO 4

RCO 2

RCO 1

Physical no.

Содержание AlphaCom XE Series





































































Результаты поиска

Содержание AlphaCom XE Series

Отзывы:

Похожие инструкции для AlphaCom XE Series

Бренды по названию

Популярные бренды

Vingtor Stentofon AlphaCom XE Series, Установка, настройка и эксплуатация

Результаты поиска

Содержание AlphaCom XE Series

Отзывы:

Похожие инструкции для AlphaCom XE Series

Бренды по названию

Популярные бренды