vimec V 64 Скачать руководство пользователя страница 8

Страница: 8 / 64

7511131

5) INTENDED AND IMPROPER USES OF THE ST AIRLIFT

5.1) Intended uses

The Mod.

V64/74

stairlift is a system for transporting one person

SEATED ON A WHEELCHAIR OR ON

A SPECIAL SEAT (optional)

with

STRAIGHT

rail at

CONSTANT

gradient which can be installed on stairs

having the following characteristics:

- Ambient:

Indoor and outdoor

- Steps:

Parallel

- Gradient:

Minimum 0° - Maximum 50°

User characteristics: Self-sufficient, physically and mentally suitable, familiar with the equipment’s

operation and the use and maintenance instructions.

WARNING: If the person using the system is not self-sufficient, the stairlift must be operated

by another person acting as attendant. While the lift is in motion, sit still and do not move or rock.

5.2) Improper uses

- Transporting objects on the platform

- Overloading the stairlift (e.g., disabled person with electric wheelchair having total weight in excess

of the maximum permitted load. See section 4, Technical Specifications).

- Use of the stairlift by unauthorised persons (e.g. children, people who do not meet the requirements

specified in point 5.1)

Improper uses

Problems

Use on stairs having gradient

greater than 50°:

Overheating of motor

User standing on platform:

Risk of falling

Operation by unsuitable operator:

Risk of falling

Transporting more than one person:

Risk of falling and of overheating of motor

WARNING: DO NOT MAKE MODIFICATIONS INTENDED FOR ANY USE, DO NOT INSERT EXTRA-

NEOUS OBJECTS OR LIQUIDS IN HOLES OR CRACKS, DO NOT SPRAY LIQUIDS ONTO THE STAIRLIFT

6.1) Preliminary checks

Checks to be made before the lift is put into service.

Skill level: OS - Specialist operator appointed by the manufacturer.

ORGANO CONTROLLATO

RISULTATO DEL CONTROLLO

ITEM CHECKED

RESULT OF CHECK

Controls:

Correct operation in response to controls.

Correct timing of the start-up controls.

Efficiency of emergency stop.

Safety devices:

Check that the safety device is tripped, stopping the lift.

- Sensor edges

- Electric limit switches

- Over-run safety device

- Anti-crushing platform base

Power supply:

Mains voltage and frequency as specified in point 6.2.

Earth connection:

Check that the lift system’s earth line is connected to the earth

line of the mains system.

6) PREPARATION FOR COMMISSIONING

7512131

Содержание V 64

































































Результаты поиска

Содержание V 64

Отзывы:

Похожие инструкции для V 64

Бренды по названию

Популярные бренды

vimec V 64, Использование и обслуживание

Результаты поиска

Содержание V 64

Отзывы:

Похожие инструкции для V 64

Бренды по названию

Популярные бренды