Vimar 01913 Скачать руководство пользователя страница 35

Страница: 35 / 84

The GSM chronothermostat will send the following SMS response message:

GSM-01913 1/1

SMS redirection

on number of

index 1

To turn off this redirecting function, send the following SMS:

<user code>.RED.NUM0

(zero)

The GSM chronothermostat will send the following SMS response message:

GSM-01913 1/1

SMS redirection

Disabled

To query the chronothermostat and view the number on which the redirecting has been set, send an SMS
in the form of:

<user code>.?RED

If the function is enabled and associated with the phone number saved in position

<n>

, the GSM

chronothermostat will send the following SMS response message:

GSM-01913 1/1

SMS redirection
on number <n>

Vice versa, if the function is not enabled, the GSM chronothermostat will send the following SMS:

GSM-01913 1/1

SMS redirection

Disabled

Содержание 01913





















































































Результаты поиска

Содержание 01913

Отзывы:

Похожие инструкции для 01913

Бренды по названию

Популярные бренды

Vimar 01913, Инструкция по эксплуатации

Результаты поиска

Содержание 01913

Отзывы:

Похожие инструкции для 01913

Бренды по названию

Популярные бренды