Vimar 01913 Скачать руководство пользователя страница 57

Страница: 57 / 84

To disable it, send the following SMS message:

<user code>.AR.OFF

Note

: No response SMS message is required from the chronothermostat 01913�

Example
If the set user code is the default 1234 and you want to disable management of the alarm for no mains
power/restored mains power, send the following SMS:

1234.AR.OFF

To read the setting made on the alarm for no mains power/restored mains power, send the following
SMS message:

<user code>.?AR

The chronothermostat 01913 will send an SMS reply message with the following format:

GSM-01913 1/1

ENABLED:ON/OFF

TOFF:5s

TON:5s

Example�
If the set user code is the default 1234 and the alarm for no mains power/restored mains power has
been enabled, on sending the SMS message:

1234.?AR

The chronothermostat 01913 will send the following SMS response message:

GSM-01913 1/1

ENABLED:ON

TOFF:5s

TON:5s

Содержание 01913





















































































Результаты поиска

Содержание 01913

Отзывы:

Похожие инструкции для 01913

Бренды по названию

Популярные бренды

Vimar 01913, Инструкция по эксплуатации

Результаты поиска

Содержание 01913

Отзывы:

Похожие инструкции для 01913

Бренды по названию

Популярные бренды