background image

PRODUCT MANUAL

Designed, Manufactured and Supported in the USA

C O M M U N I C A T I O N   &   S E C U R I T Y   S O L U T I O N S

VoIP Tower Phones

ADA Compliant VoIP

Emergency Tower Phones

February 26, 2019

VIKING

Features

Applications

Specifications

www.VikingElectronics.com

Information: 715-386-8861

ADA Compliant VoIP Tower Phones with

Blue LED Beacon and Strobe Light

•  Automatic polling and programming software included
•  SIP compatible (see page 2 for list of compatible IP-PBX phone systems)

•  Outbound Proxy, Authentication ID, Peer to Peer, VLAN Tagging

•  PoE powered (class 1, <4 Watts)
•  Automatic Noise Canceling (ANC) for operation in noisy environments
•  VoIP eliminates the need for “Push to Talk” mode
•  Network downloadable firmware
•  Meets ADA requirements for Emergency Phones:

- Automatically lights the “Call Connected” LED
- Transmits a location I.D. or voice announcement
- Grade 2 Braille label for the visually impaired

•  Non-volatile digital voice announcer with 28 seconds of voice memory
•  Handsfree operation
•  Marine grade 316 stainless steel prevents faceplate / push button corrosion 
•  Dials up to 5 emergency numbers
•  

E-1600BLT2IPEWP

and 

E-1600AST2IPEWP 

can also dial up to 5 additional

non-emergency “INFO” numbers

•  Cycles through backup phone numbers on busy or no-answer
•  Comes standard with Enhanced Weather Protection (EWP), EWP products

are designed to meet IP66 Ingress Protection Rating, see 

DOD 859

•  Hangs up on busy signal, time-out or touch tone command
•  Remotely programmable 
•  Extended temperature range of -40°F to 140°F
•  Optional 

PB-100

Polling System available (

DOD 232

)

•  Diagnostics for testing microphone, speaker, and relay

•  Campus Security Sites
•  Area of Refuge sites
•  Parking Ramps/Lots
•  Automated Tellers (ATM)
•  Entryways
•  Roadside Emergency Sites
•  Stairwells in Public Buildings 

The 

E-1600-BLTIPEWP, E-1600BLT2IPEWP, E-1600-ASTIPEWP

and 

E-1600AST2IPEWP

ADA

Compliant VoIP Emergency Tower Phones are designed to provide quick and reliable handsfree
communication for SIP VoIP phone systems with PoE. The tower phones meet ADA requirements for
emergency telephones, and can be programmed from any touch tone phone or PC on the same LAN
or remotely using a static IP address. The phones can dial up to 5 programmable emergency numbers.
In addition,  the 

E-1600BLT2IPEWP

and 

E-1600AST2IPEWP 

feature a second "

INFO

" button that will

dial up to 5 non-emergency numbers.

At the simple push of a button, the Tower Phone will initiate a call to your emergency personnel and
send a digital announcement to identify the location of the emergency call.  In addition, the tower phone’s
bright LED strobe light will instantly begin flashing to deter further activity and make it fast and easy for
Police or Security personnel to locate the site of the emergency. The strobe light can also be programmed
to provide a continuous-on lower intensity beacon when the emergency phone is not in use.

All four Tower Phone Models are equipped with Enhanced Weather Protection (

EWP

) for outdoor

installations where the unit is exposed to precipitation or condensation.  EWP products feature foam
rubber gaskets, sealed connections, gel-filled butt connectors, as well as urethane or thermal plastic
potted circuit boards with internally sealed, field-adjustable trim pots and DIP switches for easy on-site
programming. For more information on EWP, see

DOD 859

.

Installation requires the assistance of a Network Administrator / IT Technician.

!

E-1600-BLTIPEWP

E-1600-ASTIPEWP

E-1600BLT2IPEWP

E-1600AST2IPEWP

Phone Power:  

PoE class 1 (<4 Watts)

Beacon/Strobe Power: 

120VAC / 12VDC power adapter (included) 

Maximum Sound Pressure: 

90 dB SPL @ 1m 

Dimensions: 

See Installation and Specifications

Operating Temperature: 

-40°F to 140°F (-40° C to 60° C)

Humidity:

Up to 100%

Audio Codecs: 

G711u, G711a, G722

Network Compliance: 

IEEE 802.3 af PoE, SIP 2.0 RFC3261,

100BASE-TX with auto cross over

Connections: 

(1) RJ45 10/100 Base-T, (3) gel-filled butt connectors

Содержание E-1600-ASTIPEWP
























Отзывы: