9
E-1600-20-IP
Front View of Optional
VE-5x5 (not included)
2.25”
Condensation
Drain Hole
5.14”
5.22”
3.25”
4.0"
Rear View of Optional
VE-5x5 (not included)
(2) 0.2 x 0.43 slots for
single gang box
(4) 0.2 x 0.43 slots for
double gang box
(1) 0.74"
diameter
3.0” 3.3”
3.0”
2.1”
Wall Stud
* Front View of
Plastic Rough-In
Box (included)
** Wire knock out
(2) Standard flat head
dry wall (sheet rock)
screws (not included)
(4) 0.38” diameter
(for gooseneck
pedestal mounting)
Peel paper liner and adhere gasket
to back of panel, centering over
mounting holes.
Caution:
For rough
surfaces (ie: brick, stucco, etc.)
additional caulking may be required.
(4) T-10 Torx stainless steel,
flat head, security screws
and drive bit (included)
Optional VE-5x5 Surface Mount Box with black satin powder paint finish, not
included (DOD 424). Optional VE-LIGHT kit can be used to illuminate the faceplate
when used with a VE-5x5 (DOD 428). WARNING: Do NOT use a wet location box.
The optional
VE-5x5
Surface
Mount Box (left) is designed to be
surface mounted to a single gang
box, double gang box or
VE-GNP
Gooseneck Pedestal. For more
information on the
VE-5x5
and
VE-GNP
, see DOD 424.
Important:
The
E-1600-20-IP
will
NOT
mount to a standard double
gang box. If your applications
requires a double gang box, see
model
E-1600A-22-IP
on page 10.
|
OR
|
Grade 2 Braille Label
"Help" Push to Call Button
Call Connected Red LED
"Info" Push to Call Button
INFO
HELP
CALL
CONNECT
ED
Condensation
Drain Hole
Marine grade 316 stainless
steel faceplate and push button
switches (sealed per IP67)
Laser Etched Graphics
*
Note:
The black plastic rough-in box (
part # 259576
) may be purchased separately (
Example:
Mounting boxes to studs before the
walls are finished for flush installation). Go to
www.vikingelectronics.com
and click on “
Spare Parts
” to order these rough-in boxes.
** Caution:
When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent
condensation from accumulating inside the
E-1600-20-IP
always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4”
diameter hole in the bottom of the black plastic box.
Dimensions:
Overall - 127mm x 127 x
57mm (5.0” x 5.0” x 2.25”), Plastic
Electrical Box - 102mm x 102mm x
54mm (4.0” x 4.0” x 2.14”)
Shipping Weight:
1 kg (2.12 lbs.)
Front Panel Material:
14 gauge Marine
grade 316 brushed stainless steel
Connections:
Gel-filled butt connectors
Optional Enhanced Weather Protection (EWP) Available:
The optional EWP
products feature foam rubber gaskets and boots, sealed connections, gel-filled butt
connectors, as well as urethane or thermal plastic potted circuit boards. See
DOD
859
.
Mounting with Plastic Rough-In Box (included):
Flush into walls, mounts to side
of wall stud.
Mounting with Optional VE-5x5:
Surface mount to walls, single gang
boxes, double gang boxes, posts, or to a Viking
VE-GNP
Gooseneck pedestal (see
DOD 424
for more information).
Note:
When mounting outside to rough or uneven surfaces (brick, stucco, etc.) apply
a bead of clear silicone caulking around the top edge / sides of faceplate or
VE-5x5
.
Note:
When European CE compliance is required, mount in optional
VE-5X5
metal enclosure.
