manualshive.com logo in svg

Viessmann VITODENS 333-F WS3A, Инструкция по эксплуатации, Страница: 89 / 124

Поделиться
Скачать
Viessmann VITODENS 333-F WS3A Скачать руководство пользователя страница 89

Then standard control mode
resumes.

2.

Note the rotational direction of the
mixer motor during its self-test.
Then set the mixer manually to
"Open" again.

Note

The flow temperature sensor must
now capture a higher temperature.
If the temperature drops, either the
motor is turning in the wrong direc-
tion or the mixer set is incorrectly
fitted.

Mixer installation instruc-
tions

Changing the rotational direction of the mixer motor (if required)

Danger

An electric shock can be life-threatening.
Before opening the equipment, switch OFF the ON/OFF switch and
mains voltage, for example at the fuse or the main isolator.

A

ON/OFF switch

B

Rotational direction switch

1.

Remove the lower and upper hous-
ing cover of the extension kit.

Extension kit installation
instructions

Repairs

(cont.)

89

Troubleshooting

5692

731

GB

Содержание VITODENS 333-F WS3A





























































































































Отзывы:

Нет отзывов