manualshive.com logo in svg

Videx GSM Lite 4000 Series, Техническое руководство

Поделиться
Скачать
Videx GSM Lite 4000 Series Скачать руководство пользователя страница 45

66250756-EN - V2.1 - 05/11/19 

- 45 -

4000 Series GSM Lite Audio Intercom - Technical Manual

4000 Series GSM Lite Audio Intercom

Double beep, a single 
short beep followed by a 
long beep.

Button pressed but no number stored.

Program a telephone number for the button 
pressed.

Long beep followed by 
short beep while the 
system is in standby.

Invalid text message received.

If this has happened when sending one of the 
programming text messages then check the 
message for errors. These beeps will also be heard 
if the 4 digit code in the text message is incorrect. 
If you are unsure of the 4 digit code, try resetting 
it to 1111.

Double beep.

Button pressed, GSM LITE dialling stored 
number.

None, this is normal.

Long beep while the 
system is in use.

Manually ending/cancelling a call by pressing 
another call button.

None, this confirms the call has been cancelled. 
Another call can be placed if required.

Four long beeps.

Not registered with a network provider but still 
trying.

Leave it a short while to see if it manages to find 
the network. If the beeps repeat every 30 seconds 
then try moving the antenna to a better location 
or changing the SIM to another network provider.

Six long beeps.

Unknown registering problem.

Try moving the antenna to a better location. 
Try changing the SIM card to another network 
provider.

Single short beep every 
10 seconds after power 
up.

Unable to see the SIM card.

Check the SIM card is fitted correctly. Try removing 
the SIM card, cleaning and fitting again. Try a 
different SIM card.

Short beep, long beep 
repeated 3 times.

Call button pressed and either the call is on divert 
to the master number or there is no master number 
stored.

This may be the required setup but if it’s not then 
either check and store a master number to divert 
the calls to or open the switch between 

AO1

 & 

g

 

used to switch the calls into divert mode.

Additional User Information

Содержание GSM Lite 4000 Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды