66250756-EN - V2.1 - 05/11/19
- 38 -
4000 Series GSM Lite Audio Intercom - Technical Manual
4000 Series GSM Lite Audio Intercom
Programming the GSM Intercom
The default for this function is disabled (set to 00). The following texts can be used to enable or disable this function.
1111EDZnn
Set the dial ‘0’ function nn: 01 or 00 (01 = enable, 00 = disabled).
1111EDZnn?
Set the dial ‘0’ function nn: 01 or 00 (01 = enable, 00 = disabled) also send a confirmation
text back to the sender.
1111EDZ?
Query the dial ‘0’ mode set.
When this feature is set the user answering the call must press ‘
0
’ on their phone to accept the call otherwise the call will be diverted
to the second (divert) number.
ENABLE THE # (HASH) FUNCTION (ED#)
Once enabled the end user must press the
#
button on their phone before pressing any other button (also refer to the user command
table on page 43) with the exception of when the user needs to enter the 4 digit programming code
“1111”
.
The user will have up to 3 seconds to press the user command button (e.g. button
3
to activate the relay), if the user doesn’t press
the next button within the 3 second window they will have to press the
#
button again.
By default this function is disabled (set to 00). The following texts can be used to enable or disable this function.
1111ED#nn
Set the # function nn: 01 or 00 (01 = enable, 00 = disabled).
1111ED#nn?
Set the # function nn: 01 or 00 (01 = enable, 00 = disabled) also send a confirmation text
back to the sender.
1111ED#?
Query the # mode set.
FIND A TELEPHONE NUMBER (FDT)
The find a telephone number feature allows the user to find the dial to open location (between 000 - 099) of where a particular
telephone number is stored in the GSM LITE intercom. It can locate the number either from using the full telephone number or a
minimum of the last 4 digits of a number (see following examples). The following text messages can be used.
1111FDT”yyyyyyyyyyy”?
Find dial to open location of telephone number yyyyyyyyyyy stored, where yyyyyyyyyyy
= telephone number (minimum of 4 digits).
Example 1:
Find dial to open location of the telephone number using the full number
01234567890
, the following text can be
sent to the GSM LITE intercom:
1111FDT”01234567890”?
The GSM intercom will reply with the following text:
STORED IN nnn
OK VIDEX GSM
where nnn = the dial to open location of where the number is stored.
Example 2:
Find dial to open location of the telephone number using the last 4 digits of the number
4567
, the following text
can be sent to the GSM LITE intercom:
1111FDT”4567”?
The GSM intercom will reply with the following text:
STORED IN nnn
OK VIDEX GSM
where nnn = the dial to open location of where the number is stored.
END ON LAST DIVERT (EOD)
The end on last divert feature allows the GSM intercom to ring the programmed divert number as usual and if the divert number is
not answered within the divert time it will then end the call. It will also end the call if there is no divert number stored in the GSM
intercom.
By default this feature is disabled (set to 00), but can be enabled (set to 01). The following programming commands can be used to
set/check the end on divert function.
1111EODnn
Set end on last divert to nn, where nn = 00 (disabled) or 01 (enabled).
1111EODnn?
Set end on last divert to nn, where nn = 00 (disabled) or 01 (enabled). Also send a
confirmation text back to the sender.
1111EOD?
Query the end on last divert status stored in the GSM module.
