manualshive.com logo in svg

Videx GSM Lite 4000 Series, Техническое руководство

Поделиться
Скачать
Videx GSM Lite 4000 Series Скачать руководство пользователя страница 40

66250756-EN - V2.1 - 05/11/19 

- 40 -

4000 Series GSM Lite Audio Intercom - Technical Manual

4000 Series GSM Lite Audio Intercom

UNLATCH PREVENTION FEATURE (LLA)

The unlatch prevention command 

LLA

, when enabled, will prevent a programmed latched output (the GSM’s relay or the auxiliary 

output) from being inadvertently unlatched by a DTO number or by pressing the relevant button (

3

) on the phone during a call. 

Even when this feature is enabled if either the GSM’s relay or the auxiliary output have been setup to latch they can still be unlatched 
using the relevant 

1111RUL

 or 

1111A1U

 programming command.

By default this feature is disabled (set to 00), but can be enabled (set to 01). The following programming commands can be used to 
enable/disable and check the unlatch prevention feature.

1111LLAnn

Set the unlatch prevention feature to nn, where nn = 00 (disabled) or 01 (enabled).

1111LLAnn?

Set the unlatch prevention feature to nn, where nn = 00 (disabled) or 01 (enabled). Also 
send a confirmation text back to the sender.

1111LLA?

Query the status of the unlatch prevention feature stored in the GSM module.

Programming the GSM Intercom

Содержание GSM Lite 4000 Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды