manualshive.com logo in svg

Videx GSM Lite 4000 Series, Техническое руководство

Поделиться
Скачать
Videx GSM Lite 4000 Series Скачать руководство пользователя страница 24

66250756-EN - V2.1 - 05/11/19 

- 24 -

4000 Series GSM Lite Audio Intercom - Technical Manual

4000 Series GSM Lite Audio Intercom

PANEL CARE

The door panel’s facia is either a stainless steel mirror or matt finish, or matt finish aluminium. 
It is important that the facia is cleaned on regular occasions to prevent dirt build up and 
tarnishing of the metal.

A clean and soft cloth can be used with moderate warm water or non-aggressive cleansers. 
Additional care should be taken to follow the grain of the metalwork when polishing panels 
with a matt finish and always only polish in one direction to avoid light scratching of the 
plate, see 

Fig29

. Also try to avoid any polish build up around the panel’s buttons which may 

prevent the buttons from operating correctly.

DO NOT USE ANY OF THE FOLLOWING:

• Abrasive liquids;

• Chlorine-based liquids;

•  Metal cleaning products (including Sidol stainless steel cleaner as this can affect the 

etching and/or engraving);

• Hydrochloride bleaches.

Fig. 29

 

IMPORTANT NOTE: IT IS IMPORTANT TO REGULARLY MAINTAIN THE “UP KEEP” OF THE GSM LITE PANEL (CLEANING 
AND GENERAL MAINTENANCE ETC.) ANY FAULT OR DAMAGE THAT MAY OCCUR TO THE GSM LITE PANEL DUE TO 
THE LACK OF CLEANING AND MAINTENANCE IS NOT THE RESPONSIBILITY OF VIDEX.

General Directions for Installation

Содержание GSM Lite 4000 Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды