manualshive.com logo in svg

Videx GSM Lite 4000 Series, Техническое руководство

Поделиться
Скачать
Videx GSM Lite 4000 Series Скачать руководство пользователя страница 2

66250756-EN - V2.1 - 05/11/19 

THE POWER TO SECURE

- 2 -

4000 Series GSM Lite Audio Intercom - Technical Manual

4000 Series GSM Lite Audio Intercom

EU RoHS DECLARATION OF CONFORMITY

2G version

Telit Communications certifies that the GL865-QUAD V3 (Quad Band GSM850/EGSM900/DCS1800/PCS1900 GPRS Wireless Module) 
is in conformity with Directive 2011/65/EU of the European Parliament and the Council of 8th June 2011 on the restriction of the 
use of certain hazardous substances in electrical and electronic equipment. The conformity with the applicable requirements of the 
Directive 2011/65/EU has been demonstrated against the following harmonized standard: EN 50581:2012 Technical Documentation 
for the assessment of electrical and electronic products with respect to the restriction of hazardous substances.

3G version

Telit Communications certifies that the UL865-EUR (Dual Band 2G EGSM900/DCS1800 and Dual Band 3G FDD I/FDD VIII Wireless 
Module) is in compliance with the essential requirements and other relevant provisions of European Directive 1999/5/EC (R&TTE). 
The conformity with the essential requirements of the Directive 1999/5/EC has been demonstrated against the following harmonized 
standards:

Article of Directive 1999/5/EC

Harmonized Standard Reference

Health & Safety (R&TTE art. 3.1a)

EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + AC2011
EN 62311:2008

EMC (R&TTE art. 3.1b)

EN 301 489-1 V1.9.2
EN 301 489-7 V1.3.1
EN 301 489-24 V1.5.1

RF Spectrum use (R&TTE art. 3.2)

EN 301 511 V9.02
EN 301 908-1 V5.2.1
EN 301 908-2 V5.2.1

WARNING!

To comply with FCC RF exposure requirements, a separation distance of 20cm (7.87”) or more 

must be maintained between the antenna of this product and all persons.

Separate FCC approval for this product is not required as it will be classed as a fixed installation.

THIS PRODUCT IS NOT DESIGNED TO BE USED AS AN EMERGENCY CALL POINT.

MANUFACTURER

All Countries:

VIDEX ELECTRONICS S.P.A.

www.videx.it - [email protected]
Tel: +39 0734-631699 - Fax: +39 0734-632475

The product is CE marked demonstrating its conformity and is for distribution 
within all member states of the EU with no restrictions. This product follows 
the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU 
(LVD); 2011/65/EU (RoHS): CE marking 93/68/EEC. 

UK Customers:

VIDEX SECURITY LTD.

www.videxuk.com - [email protected]
Tech Line: 0191 224 3174 - Fax: 0191 224 1559

CUSTOMER SUPPORT

VIDEX ELECTRONICS S.P.A.

Via del Lavoro, 1 - 63846 Monte Gilberto (FM) Italy
Tel: (+39) 0734-631699 - Fax: (+39) 0734-632475
www.videx.it - [email protected]

Declaration of Conformity

Содержание GSM Lite 4000 Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды