Videology 20Z704T-PZ10 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 40

Videology 20Z704T-PZ10 Скачать руководство пользователя страница 16

7.5.3. Video Connection

Connect with BNC coaxial cable

7.5.4. Network Connection (Reserved for future network models)

7.5.4.1. NETWORK

1

Connect with LAN cable.

If LAN cable is not connected properly, This product can not be operate.

7.5.4.2. NETWORK 2 (Reserved for supplier.)

DO NOT CONNECT WITH ANY DEVICE.

7.5.5. Alarm Input Connection

Sensor Input (open collector example)

Before connecting sensors, check driving voltage and output signal type of the sensor. Since

output signals of sensors are either Open Collector or Voltage Output type. In general, the
cabling must be done properly depending on which is used.

Signal

Description

IN COM+

Connect (+) cable of electric power source for Sensors to this

port as shown in the circuit above.

IN1

−

, IN2

−

, IN3

−

, IN4

−

Connect output of sensors for each port as shown in the circuit
above.

If you want to use Alarm Input, the types of sensor must be selected in the OSD menu.

The sensor types are Normal Open and Normal Closed. If the sensor type is not selected

properly, the alarm can be activated in reverse.

Normal Open

Output Voltage is high state when sensor is activated

Normal Close

Output Voltage is high state when sensor is not activated

Doc # INS 20Z704T-PZ10

Issue Date: 08/13/2009

Revision: B

Page 16 of 40

«
...
14
15
16
17
18
...
»

Содержание 20Z704T-PZ10









































Отзывы:

Нет отзывов