Victron energy Multi RS Solar Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 51

background image

Multi RS Solar

48/6000

Protection (6)

a - g

Data Communications

VE.Direct port, VE.Can port & Bluetooth (7)

General purpose analog/digital in
port

Yes, 2x

Remote on-off

Yes

Operating temperature range

-40 to +65°C (fan assisted cooling)

Humidity (non-condensing)

max 95%

ENCLOSURE

Material & Colour

steel, blue RAL 5012

Protection category

IP21

Battery-connection

M8 bolts

PV Connection

2 positive & 2 negative MC4

230 V AC-connection

Screw terminals 13 mm² (6 AWG)

Weight

11 kg

Dimensions (hxwxd)

425 x 440 x 125 mm

STANDARDS

Safety

EN-IEC 60335-1, EN-IEC 60335-2-29, EN-IEC 62109-1, EN-IEC 62109-2

Emission, Immunity

EN 55014-1, EN 55014-2 EN-IEC 61000-3-2, EN-IEC 61000-3-3

IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3

1) Can be adjusted to 60 Hz

2) MPPT operating range is also constrained by battery voltage - PV VOC should not exceed 8x battery float voltage. For
example, a 52,8V float voltage results in a maximum PV VOC of 422,4V. See product manual for further information.

3) A higher short circuit current may damage the controller if PV array is connected in reverse polarity.

4) The maximum charge current from the built in MPPT is 80A, to reach the 100A maximum charge current of the unit
requires additional AC PV connected.

5) Programmable relay which can be set for general alarm, DC under voltage or genset start/stop function, including
minimum closed time and relay-off delay. DC rating: 4A up to 35VDC and 1A up to 70VDC

6) Protection key:

a) output short circuit

b) overload

c) battery voltage too high

d) battery voltage too low

e) temperature too high

f) 230 VAC on inverter output

g) Solar earth leakage

7) The Multi RS Solar is not currently compatible with VE.Smart Networks. Connection to a GX device (i.e. Cerbo GX) must
be made via the VE.Can interface. The VE.Direct interface is for connection to the GlobalLink 520.

Multi RS Solar

Page 38

Technical Specifications

«
...
40
41
42
43
44
...
»

Содержание Multi RS Solar




















































Отзывы:

Нет отзывов

Похожие инструкции для Multi RS Solar

Бренд: Eco Drive Страницы: 138

Бренд: Parker Страницы: 36

Бренд: Growatt Страницы: 45

Бренд: Patton electronics Страницы: 16

Бренд: Sigineer Power Страницы: 39

Standard Extreme RAKK dac Mark III

Бренд: Raleigh Audio Страницы: 65

Бренд: Kramer Страницы: 15

Бренд: PEAK COMMUNICATIONS Страницы: 18

Smart AC Inverter 100 USB

Бренд: Wagan Страницы: 5

Бренд: Elabs Страницы: 10

Бренд: SolaX Power Страницы: 2

Бренд: SAJ Страницы: 2

Бренд: Schüco Страницы: 48

Бренд: Ubiquiti Страницы: 16

Бренд: Transition Networks Страницы: 8

Бренд: Domain Surgical Страницы: 60

Бренд: Hitachi Страницы: 20

Бренд: Hitachi Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды