manualshive.com logo in svg

Victron energy CCGX, Инструкция по эксплуатации

Поделиться
Скачать
Victron energy CCGX Скачать руководство пользователя страница 22

Last update: 2018-08-21 10:10

ccgx:start

https://www.victronenergy.com/live/ccgx:start

https://www.victronenergy.com/live/

Printed on 2018-08-21 11:59

Configuration:

Connect the battery communications cable to the CCGX according to the instructions.

1.

In the CCGX, in Settings → System setup, verify that the selected Battery Monitor is the battery.

2.

Note that the Battery Monitor setting in VEConfigure3 is irrelevant. For systems like this, changing this
setting will have no effect on the charge or any other parameters in this type of system.

Other system types

When there are more chargers, or loads, connected to the battery than just the Multi or MPPT Solar
Chargers, a dedicated Battery Monitor will be required. Examples are:

House loads in Marine or Vehicle system.
PWM Solar Chargers
AC chargers, such as Skylla-is, Phoenix chargers, non Victron chargers, etc.
Alternators
DC-DC chargers
Wind turbines
Hydro turbines

Configuration:

Configure all BMV parameters (see BMV documentation)

1.

In the CCGX, in Settings → System setup, verify the selected Battery Monitor. It should be the

2.

BMV Battery Monitor.

Note that the Battery Monitor setting in VEConfigure3 is irrelevant. For systems like this, changing this
setting will have no effect on the charge - or any other parameters - in this type of system.

2.4.2 Notes

Note that this is all about showing an accurate state of charge to the user, rather than being
required for an efficient system. The SOC percentage is not used for normal battery charging. It
is, however, required when a genset needs to be started and stopped automatically based on
battery SOC.
For hub-2 installations we recommend you do not add a BMV to the system as it will only
confuse the user when there are two SOCs with different readings being displayed.

More information:

VRM Portal FAQ - difference between BMV SOC and VE.Bus SOC
CCGX Manual - configurable parameters

. See Battery Monitor selection and Has DC System.

2.4.3 Selecting SOC source

(Settings → System Setup → Battery monitor)

In the image below you can see a range of selectable choices for the SOC values which are shown in
the main Overview screen. Choose the source you want to see on the main Overview screen of your

Содержание CCGX




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды