Victory BX510H Скачать руководство пользователя страница 8

Страница: 8 / 74

Operator’s Manual Victory BX510H

- Page 8 of 74 -

Version 2.0

INTRODUCTION

2.1

About This Manual

This Operator’s manual belongs to the owner of the Victory BX510H woodchipper.

Read this Operator’s Manual before operating the BX510H

•

Pay special attention to safety precautions presented in this manual, as
they prevent accidents causing machine damage, human injury, or
death.

•

This machine can be dangerous. Therefore, reading this manual
entirely before the operation is essential.

•

This manual describes characteristics unique to woodchipper BX510H.

•

In this manual, safety is a priority. By reading it, you will become aware
of the dangers and hazards of operating this machine.

2.2

Manual Update

Reason for raising the Operator’s manual to version 2.0:

Editorial update according to Standard

IEC 82079.

Graphics and layout improved.

2.3

Explanation Documentation

Chapter 3; 'Introduction' and Chapter 4, 'Safety' is essential for anyone working on the machine.

For operators is essential:
- Chapter 5; Operation.

For Service and Maintenance personnel is essential:
- Chapter 5; Operation.
- Chapter 7; Other activities.
- Chapter 8; Maintenance.

For Product management is essential:
- Chapter 14; Specifications.

2.4

List of Abbreviations

PTO:

Power Take Off.

ASME:

American Society of Mechanical Engineers.

PPE:

Personal Protective Equipment.

Содержание BX510H











































































Результаты поиска

Содержание BX510H

Отзывы:

Бренды по названию

Популярные бренды

Victory BX510H, Руководство оператора

Результаты поиска

Содержание BX510H

Отзывы:

Бренды по названию

Популярные бренды